Search results

Morning all, just after some advice/input, so I've knocked the garage down and have now exposed the party wall which is just a single brick wall between our new walkway and the inside of the neighbours garage. The collums on show go through into the neighbours garage , would you be inclined here...

What do you mean ?

Thanks Woody, is this just something both parties keep for future reference..i.e.. there is no need to get anyone else involved

Our house is the one on the left of the picture, its a 2 storey extension. After knocking our garage down I have agreed to make good my neighbours side with new facia and to redo the felt and flashing and guttering to the side of there garage. I can't find anything online to show a similar...

Hi I'm just wondering if the P.W.A is required in this situation (pic is attached). Neighbours are fine with the works but I'd like to cover both parties and do it by the book. The centre of the 2 garages is the boundary wall, we will be extending from the house to 1 meter away from the...

Cheers mate. I'm putting a new DB in tomorrow so I'm going to take that SWA in to the new DB on its own RCBO. It was more about wether i needed a 100ma rcd between the tails and the main switch however the idea of ditching the rcd main switch in the garage is a good one

Evening all, I'm just after some clarification on what set up is best/required by the regs.. TT system , cable comes into the house into the cut out , tails into the meter and then out of the meter into the DB. Currently a small board with RCBOS doing lights and power and then a 40amp MCB...

Yeah same cheers

Yeah its old old switchgear, its basically 240v +240v so I would think its not actually a 3 phase supply but 2 individual single phases brought into the property. This is why my labelling of 1L1 and 1L2 could be argued isn't technically correct

Afternoon all, testing a commercial property and its on a 2 phase and neutral supply. Seperate phases i.e 480 v between phases, previous testers has labelled certain stuff 1/1 and 1/2 etc , question is would guys label this way or would you be labelling 1L1 , 1L2 etc, some might think it...

Evening all. I have a customer who has bought the above shower/sauna/steam room all singing dancing unit.. Now the 2 plumbers I know have been round with me and had a look and walked away , do these units have dedicated installers as the lads reckon its complicated kit.. Cheers P.S lads I know...

Morning all , Just after some advice , A friend of mine has an oven that loses the clock display and doesn't respond when turning the oven on , no power to the red neon light to indicate it's on, is this a selector switch issue? Not come across this fault before, left hand knob serving the grill...

Morning all I've had a few issues with the above dryer First of all the machine wasn't turning off when I pressed the stop start button , then the machine wasn't turning on when I pressed the button I opened up the machine and can see the Jockey pulley has cracked so I've ordered a new one as...

It does say in the instructions 'The unit must not be fitted to any type of thermostatic mixer valve or tap.. I presume this is different to a standardmixer tap?

Hi all.. just wondering if I can use the above water heater with a 1 hole sink and tap arrangement ?? plumber mentioned something about not using a mixer tap with this set up but I can't contact him to verify. Thanks

Good morning. I am looking to insulate my external garage. The garage is a brick building about 3m x3.5m The roof is a flat roof. Joists at 600mm The void is about 200mm I was looking to lay some wool insulation but wondered if i need to leave a gap from the ceiling and a gap from the...

I got the kingspan free I would have used will roll if I didn't. I'm going to put a 4 inch fan in the ceiling void so that will help

It's only 3 meters squared. The back walls only have a void of 100mm its down the side walls where the void is 230mm..the reason being is there are 3 brick collums down each side wall so rather than stud round each collums I decided to just run my track straight down.. Do you suggest that the...

40mm trap extender 2.44 from b and q and it's sorted