Search results

  1. I

    Fuel floods out of mower when i pour it in

    Amazon & here tomorrow £15
  2. I

    Fuel floods out of mower when i pour it in

    Ah ok. So next time I hear it chugging stop & fill it up. Dirt obviously got passed that filter in tank
  3. I

    Fuel floods out of mower when i pour it in

    I hold it and unable to blow. I’ve watched it for 20 minutes and not a drop has come out. The needle rubber tip seats and that’s it.
  4. I

    Fuel floods out of mower when i pour it in

    So for the 5th time I’ve had it apart & back together again. Done nothing different & used same parts ie haven’t swapped anything. I’ve just put fuel in tank & no leaks. I’ve also just cut my lawn. Even left it running for a few minutes & mower deck is dry. Very strange. Now I need to add 3...
  5. I

    Fuel floods out of mower when i pour it in

    Looks fine. I see fuel coming from between carb / engine block also opposite end towards air filter I see no fuel in float. I operate float & unable to blow. I let got of float & i can blow fine. I see no reason for it to do this,
  6. I

    Fuel floods out of mower when i pour it in

    The float seems light meaning no fuel in it. I just conncted fuel pipe back on & held carb in my hand & fuel came out again. So answer me this, IT can only be the float at fault here correct ?
  7. I

    Fuel floods out of mower when i pour it in

    Ive put the carb in a glass & slowly filled it with water. I can watch the float rise to the top no problem. So i would say float is fine
  8. I

    Fuel floods out of mower when i pour it in

    How can i confirm that, can i do a test somehow to confirm it ?
  9. I

    Fuel floods out of mower when i pour it in

    I used this mower for quite a while & never an issue. Ive used it this season now for 3 weeks & fine. Cutting the lawn today it started to chug & i knew it was running low on fuel. After a short while it stopped. I poured the fuel in the tank & watched it run out just as fast ?????? Ive taken...
  10. I

    Do I now need a scarifier

    I can only put it to him thanks
  11. I

    Do I now need a scarifier

    Sounds like I need to spray it with something. Moaned last week I didn’t cut all the primroses down. Customer wasn’t in so I left them all in a nice mine but that was wrong so scarifier it isn’t
  12. I

    Do I now need a scarifier

    It’s spongy to walk on & now trying to push a mower is getting harder due to it sinking into the moss.
  13. I

    Do I now need a scarifier

    Ah then thats probably not what i want
  14. I

    Do I now need a scarifier

    Been cutting this gardens grass for 5 years but two weeks ago & today I found it harder to cut it. I understand it was its first cut two weeks ago but after I cut the grass I see the deck which is on its highest setting touching the grass etc. When pushing the mower it’s like I’m on the beach &...
  15. I

    Diverted handle screw

    From a rough guide a 1/4 bsp bolt what diameter is it in mm I ask as I’m out at present and earlier I did measure it using a vernier & it was 4.8mm the pitch between each thread seemed coarse In my head 1/4 BSP is much larger.
  16. I

    Diverted handle screw

    Any idea what thread will be. Are we talking BSP or like 4mm Thanks.
  17. I

    Diverted handle screw

    It’s a fancy bolt with a large head. Don’t grub screws have an Allen key down the middle. The item in photo is the broken item in two pieces
  18. I

    Diverted handle screw

    It’s not a grub screw. The 2 items in photo should be together in 1 piece
  19. I

    Diverted handle screw

    Hi, Not sure if the title is correct name for item in question. Basically I’ve got bath taps with overhead shower connected. There is a lever / handle which when operated left or right directs water into bath or the shower. The screw that passes though the lever / handle has snapped. I’ve...
  20. I

    Unable to start MS170 so advice needed for me to rule things out

    Just to advise how I did the L screw adjustment. L screw all the way in then 1 full turn out. Warm saw for a minute or two. Turn L screw anticlockwise until engine started to slow up. Then L screw clockwise until engine started to slow up. Then got it kind of in the middle of these two...
Back
Top