Search results

Hi All, We are having new windows fitted and need to choose the bathroom window glass design. We are between Arctic (which we already have) and Tribal. Two totally different patterns and slightly worried Tribal will look too fussy. It all depends on scale. Has anyone got a photo of tribal in...

Hi All, So I have a Pyronix enforcer (with the WiFi module) fitted around 2022. Albeit I don't know who by, as we bought the house in 2024. I changed all the shock sensor batteries a few months ago and one PIR that was flagging as low, but not any of the other contact sensors or PIRs...

So I just noticed my boiler is sitting at 0.6 to 0.7 bar and it should be closer to 1-1.2 bar. I looked at a few online videos but none seem to match my config. I thought the yellow lever would do something, but seemingly not. How do I get a bit more pressure into the boiler ? Thanks in...

Hi All, I have just moved into a new property and noticed whilst up on a ladder this hole to the side of the lead roof (above a bay window). Annoyingly it is somewhat new, but a tile must have fallen on it. Any suggestions on how to patch it? There are no water leaks inside the property. I...

Hi All, We have just bought a house and it had a recent extension in 2022 (so will be modern construction methods). My problem is this, I have a 77" LG G2 ready to go on the wall but I have sockets already in place, on this model the bracket ount is at the top and the bracket is very flush...

Hi All, We have just moved into a house that recently had an extension built. Basically it seems that in the utility part of the extension, the wiring is connected to a 63a 30ma RCD in a new consumer unit. On this single ring, there are 3 double sockets. The way I plan to use the sockets are...

We currently have a vinyl floor that extends to the back wall under the kitchen units. Is it best to cut the vinyl back so the washing machine and tumble dryer sit on concrete ? Or will it be fine on the vinyl? Thanks

Hi All, I have just moved into a new property that has a wireless pyronix enforcer alarm. Now the first issue, I can't engage the alarm 1) It says 30 - Car "tamper on input" . So it seems this is either a loose case or a faulty battery, I naturally went into the garage and found a contact...

Hi All, I am looking at a property right now and pre-empting some of the survey points. The pointing seems to be missing in small places and "interestingly" patched in other areas. Does this still look serviceable with a bit of gap filling, or not really and needs to be done. Equally this is...

Hi All, I am just looking at a new property and noticed the fuse box looked a bit old and surrounded by lots of older looking 'stuff'. How old do you think this consumer unit is and anything that worries you about it (apart from the wiring to my eye looking a bit unkept!)

We are looking at a property and it had an extension 2 years ago (the now typical thing where the back is extended out to create a large kitchen/entertaining space with big sliding doors at the back. There was a big RSJ put across the original back wall to allow this (the extension is about...

Hi, My parents have just bought a NEST (3rd gen) and want to replace their existing LP722. It is a Y plan system with a Drayton Mid Position motorised Valve. Can you advise the mapping of these from the LP722 configuration to the NEST connections. Thank you!

Hi, I have moved into a property that has a Hive System (just the basic one for a combi i.e central heating only and not water )installed and I want to switch it for my Nest 3rd Gen. Presumably N to N, L to L The earth seems to be hanging there, so I will need to check the other end of the...

Hi All, I finally got around to installing my Nest 3rd Gen, replacing a wireless digistat RF1. I also seem to have a double set of live/neutral wires and 3 for earth, I copied this exactly from the old system/wiring matching the numbers. There was that loose blue wire before unless it came up...

Hi, I am considering a new Nest thermostat to replace my old Drayton RF1 to go with my Worcester 25i (this currently runs a really basic dip switch wheel timer). Will I be able to just put the Nest in place of the RF1? or is it more involved because of the manual timer on the boiler? If so...

I am currently looking at buying a basement flat (Victorian building) and have had a damp survey carried out. The survey suggests that horizontal/vertical DPC and tanking is required thoughout the majority of the property. I basically want to check if they have over quoted me! I have been...

We have just bought an Electrolux EHD60020P 4 Zone Induction Hob. The manual recommends the use of a HO5BB-F cable which appears to be a Flexible Cable with Elastomer Rubber Sheath 90° C , 300/500 Volt. I have connected the Hob to the existing cable and the unit powers up, but only the...