Search results

Needs replacing. Should I strip/clean the trap? Thank you.

Replaced the AAP (boiler drain cock initially a bit reluctant) - presumably the little plastic screw cap on top is not supposed to be screwed down tight? Thank you.

I used this particular (450x450) untextured matt because it has the same finish on the sides as the top. I'm trying to source similar. Any suggestions would be appreciated inc. the correct search term for this type. Maybe some sort of resin composite? Thank you.

Obvs it's sat on carcass, which isn't waterproof so I'd like a worktop added to finish it. A waterproof seal between stainless and any additional worktop is a must. I thought conventional worktop or even a 600x600 composite tile on a ply base, if I can get one that size (not sure ceramic or...

Replacing the rad so I'd like to drain this down 1st, but having fully undone the sq release nut on the drain-off spiggot it just drips. If I open the air bleed valve on the top I get water out of the air bleed, but still virtually none out of the bottom drain-off spiggot.. Thank you. Dain

Do 5"x1" door frames from Travis etc shrink much after fitting? How much would they lose from o/a width? Can you buy any that are so dry that they won't? Tnx all Dain

Obvs I'll be securing the electrics 1st. I don't really like permanent boxing. Generally, I like access available without the wrecking bar. I secure/mount floor any floor battens on plastic packers, to keep them up from the moisture. Any pointers? Thank you.

The stone was repurposed from an earlier building. Paint is sort of creamy/chalky. Washing it off using water immediately produces a virulent rust coloured stain. Any ideas?

The stonework was reclaimed/repurposed from a much earlier building. Where there is paint it's chalky creamy and turns rust red if I try to wash it off with water. Will paintstripper gel take it off and wash down without permanently staining the stonework? Generally, I'd like to clean the stone...

As a top rail for box skirting, there's a 44x21 sat on the joists for the skirting btm? I was going to set the top rail, then push some plasterboard adhesive down behind ir. I'd gun some mastic grout down behind the top rail but it stinks so much, I don't know that the smell would go away...

1900x1700 area. Probably a wet room with adjacent privy before wall came down to accommodate bath (which was below central heating boiler..). Refit inc. getting it back to regs. Also, washing machine now downstairs in bathroom. Screed highest is where the separating wall was. Does...

Moisture is getting across the void to the inner leaf, and the emulsioned skim is moulding slightly adjacent the door frame so I need some sort of vertical make-up trim externally to cover the door frame/add-on join? Is it better to recess the external render up the side of the door frame a...

What about the sheds? Tnx, Dain

I picked up some 18mm ply from B&Q earier this year for a flooring job but need a few sheets more. Is there likely to be much variation in thickness between the 1st lot and the next few sheets? Do they dry out further in the home after coming off the shelf in the sheds? Ply being fixed on CLS...

I mistakenly tried mixing and matching a new trv and a rad tail that were supplied separately. But I don't think they're a great match. I should have used the original matching trv/tail, but the tail olive has now been tightened once so..how do you get tail olives off to replace them?

Gluing & screwing ply sheets down to CLS, Toolstation has some cheap (cheaper than Egger) D4, but 10 minutes? Is there a good slower option?

I have some 8mm tails that need extending to the rad. Would it be of any benefit if I continued them to the rad valves with 10mm?

I'm putting a washing machine waste on the old sink waste 32mm spiggot/push fit collar on the soil pipe. It looks like the old sink 32mm waste going into the soil pipe was cut to length with a broken roof tile, so the seal is shot. The seat in the old grey 32mm collar is different, so a new O...

Is it ok? What's it like to solder? Can I put a compression fitting on it?

What sort of float is used when plastering/skimming around uPVC windows so the white uPVC doesn't get scratched by a steel float? I looked on Screwfix but maybe I wasn't using the right search term, I couldn't find anything that looked right. Tnx Dain