Search results

Just wondering if anyone can help,i have managed today to but a 1.5" rip in my vinyl in the middle of my lounge,,the rip is clean thankfully. What can i use to glue it strong and then what can i use to smear over the rip afterwards to keep it safe,,i read about vinyl seam sealer but i cannot...

Well you guessed it,,the front race is solid,and i mean solid,,ive belted it,swore at it,,just looked it it and i will not come out,,it dosnt help you cannot get anything in behind it with that lip! I know you said youve had it,but it there no other way of getting this out,i'd got so far with...

Thanks for that,,didnt realise it was 12 years old! its been a great machine,which is why I thought I would give it a go,,if worst comes to worst ill get a new machine. Thanks again craig

had a look and can't find a model number on the machine apart from whats on the front which is "hotpoint first edition 1200 spin wm53." its an all white one,as ive seen some with black control panels. will it be wrote internal,i can take the lid of,,only a small area to get to the shaft nut...

ahh 5 mins ill go and look for it :)

Can anyone advice if this is a nightmare job,I am very competent at repairing alsorts so no problems there,ive just not done a washer bearing before its become very noisy,and i think its time to replace,,At first i though there was something like a 5p in between the drum and outer drum,so...

Hi mate thanks for your reply,i thought that about the pipes,,but when i wipe them its like red rust coming of them,and the paint that was on them is coming off. i cant really do anythin with the marine tank its evaporation from it,a dehumidifier works not to bad but doesnt prevent. do you...

As above,my radiator is rusting on the edges,ive rubbed it down a few times and painted over it but its coming back. there is also copper piping from it in my lounge that is rusting on the outside. i know the cause its salt water from my marine tank. im not keen to change the rad and...

jobs a good one,,ill make one this weekend,cheers for that,saves me £90

Im not looking to buy a hinge jig as i only hang about 2 doors a month however i like the neat finish they do,so is it possible to just mark the hinge on the door and cut as much out free hand with the router? And what router bit do you recommend. if anyone has a nd plans to make a 3" &...

Thanks woody,,ill give one a try,,i looked on the 3m site but couldn't really find anything on them. There is a few on ebay which ive had mixed reponse on the lengh of use on them.

anyone used or got one of these :- SCREWFIX LINK HERE Ive read mised reports about people using them for a year and people saying they have to be used within one month?

Im a member on there :D but its not my usual im on a couple of other marine forums I was going to post but i thought,,a diy forum might be a better way forward with experts :D are you on UR by anychance

Thanks for that just found a few on there. Ive looked all over for the distance of the hole from the edge,for safty i think ill go a 2x just to be sure.

Sorry i should of put that :oops: thanks :D with a bit of luck it wont break,just make sure ive not had a few beers 1st.

Having a bottom drain in a marine tank is a common move,you drill the hole put a stand pipe in and you build a glas weir which sets the water hight water goes down weir and through into the sump (which houses all the equiptment and macro algaes)and the return takes it back. :) sand goes...

It is for a bottom drain how did you guess,its so i can sump the tank :D ive not really got anyone local to do it,,ive found someone who said will do it for £50 and if tank breaks he aint responsible.hmm

I have a 10mm glass fishtank and i want to drill a 55mm hole in the base. Im after some advice on drilling glass,and here is how i was thinking of doing it. use a diamond bit,,use a battery drill,shall i use on torque setting? fill the tank to say with 8mm of water,cut a hole with the...

Thanks for that,,glad i joined this forum now,,,all i need to do s find that they do run defo that way ,,its so difficult to know where the beams are with the screed stuff over the block and beams..might need to do some digging :D i was also going to bolt the stand at the back to the wall in...

Hi that has baffled me,,in easy term the tank is to heavy? :D the tank has a foot print of 3ftx2ft and 26"high plus there is an additional tank under it as a sump/filter,but thats only a tiny thing. I think the best bet might be to sell the tank and get somethin smaller. will the floor...