Search results

Hi Anyone know a good way of cleaning the interceptor traps the u bends in sewer line with clay tea pot lid. Mine is full of gravel that needs clearing. I can't physically reach in and down so need to get debris out somehow . Ideas ???? Thanks

Small cast iron rads to be fitted but existing pipework is 10mm fed from centre wall plate behind rad. Any valves available to keep in line with the look of the rad? also need drainoffs as well. Is this doable with speedfit pipe ? Thanks

Thanks for the replys and debate . After all that's why we ask the questions. I will go ahead with my original plan of 4 core 6mm because of load requirements for cabin. I know the armour can be used as earth but myself personally i always use a conductor and dont solely rely on the armours...

Hi Tncs system Log cabin 25m from house See that when exporting earth 10mm earth is the prerequisite so would it be ok to use 4 core 6mm swa and double up 2 cores effectively making 12mm for earth. And understand the need for non combustible in house ie metal consumer unit but how about...

Hi What cable is best to use for rs 45 bus connections for accessories ie rf portal can power and data be in same multi core cable?? Ta

Thanks these were just what I was looking for How does the over pipe connect to those junction boxes or do u just tape em Thanks

Hi Extension being built ground floor level. King span insulation has been put down and floor will come up another 100m to finished level. thinking of laying pipes in trunking on king span insulation . What do people use for protection of pipes ie trunking and boxes to cover joints. Where...

aaahh thanks for that explanation i even get the positive applied bit with a large value resistor to pull the 12v high when negative removed (after researching it for so long) :shock: so in my case to interface the risco agm dialer and galant panel would the negative remove work...

Can someone please help me understand the terminology involved when triggering outputs Driving me batty i have a alarm panel with negative remove outputs on trigger header i have a gsm dialler with negative remove inputs or positive remove inputs selectable via a jumper can these be...

thanksfor help sparky got it working didnt relize its all deol and fire detector zone has to be deol as well thanks i want this circuit to connect to a risco agm universal gsm dialler i didnt realize i got the stu trigger header as well can i connect the trigger header outputs direct...

i get 12 v between trigger and 0v but when i operate zone 5 the trigger doesnt change still stays 12v between 0v and trigger if this was working as it should ..should the relay coil be between ov and trigger or 12v and trigger? but trigger not changing state when i remove resistor...

can somebody please help me make sense of trigger outputs been on it for hours cant seem to get it to work trying to add a smoke alarm to ademco galant alarm panel have programmed z5 as fire zone & programmed trigger output as fire (on pcb board says trigger n/c) all i want to do is...

Hoover Can you elaborate on that pls I am planning to put both bellboxes in sab mode but supply the second bellbox with the secondary power supply The triggers wont be affected will they?

hi I also have an internal sounder and because i have this new power supply and am not afraid to use it! and if both bells can run sab mode i will. how would i connect my new power supply so one bellbox runs off this new power supply?? thanks

hi i originally did think that route but bells output of panel is 500ma and have read somewhere one texecom odyssey 3 bellbox pulls 500ma alone and in scb mode 290ma so with both running will be overloaded surely??

hi i have a galant alarm panel and want to add another texecom3 bellbox to my system. Looking at panel spec it only has 500ma protection for bellboxes I have another 12v 1a power supply i can fit in the box but what are the connections to actual feed an additional bellbox from this...

Need to fit a door contact final entry/exit zone on an inward opening all glass front door in a small shop Anybody know what best type of magnetic switch to fit or just standard one??? And best way to affix magnet to opening glass door so it doesnt come off in future. Thanks

can you freeze plastic pipe??? how about co2 cylinder and jackets, electric kits expensive$

Need to add rad to house with a boilermate 2000 in .. Havent come across one of these before, any tips on draining refilling , or is there any way of adding rad without draining the system completely down , *&^@: big house,,,@:%$ cheers

i know its not the recommended route but i already have this shower so if i connect it up will it work or am i wastin my time ? thanks i have a worcester 30 cdi combi