Search results

Hi, thanks for the reply...it ended up being the bios needing updated, can't believe it stopped the pc working but it's all good now Cheers

Hello all i have just built a pc Specs i9 9900k Msi carbon pro board 32gb 3200mhz ram Nvme 1 tb Ssd 1tb 850 Corsair psu Cpu watercooler corsair ml360r No gpu in system currently I have tried to install windows 10 via flash drive setting it to boot priority, but the screen keeps freezing at...

Hello, i have a pair of KRK rp5's speakers which i want to connect to my pc's 3.5mm audio port. My rp5's have the following connections at the back of each 1 of them ,TRS, XLR, RCA. I previously bought an RCA to 3.5mm connection for each speaker and connected them into a splitter which sounded...

compact or compact HE?, solid red light or flashing?, any strange noises from the boiler? does it happen more in the morning or night?, on heating or water? The solid red light can mean various different faults, primary sensor, venturi, pcb etc. Flashing red light possible overheat. If...

the board isnt like for like its a new gigabyte board, and works fine with my hard drive on it, sorry i cannot post blue screen because it no longer shows now :S just as i say u see windows logo and it stutters thn resets, fed up!.

bump

hi. "Water gets quite (too?) hot but little comes out of tap", little hot water comes out tap, then goes cold? or the flow of water is poor? When you create a hot water demand make sure the flow is around 9-10l/min, on dropping the front panel of the boiler ( 2 screws underneath), to the...

okay so recently replaced motherboard in my uncles computer as it was faulty, it was an msi n1996 board, in it was q6600 quad core, 4gb ram 667, 650 wd hard drive sata. when changed the board over i tried my hard drive in it as his was not available at that time, it worked fine no problems...

thanks for the fast reply, no bios or anything except screen no signal.

hi, my uncles pc is no longer working, what happened at first is he got blue screen, and then tried to restart it and then after that all that would happen is he turns all fans go, and the screen says no signal. So i've tried my screen which works fine, and same no signal, also tried my hard...

done a few different programmes for it the drum moved but very slowly and eventually struggled to move jerking back and forth. Never reached it's full spin, they're a slight buzzing noise audible too. I'm grateful of your replies, however is they're any documents on washing machine components...

viessmann boilers are very good easy installs, very spacious, good technical support, 5 year warranty, price might let you down a bit, went on a course to viessmann 10/10.

Hi, what is the boilers history any recent parts fitted that made this fault occur, or was it working fine and just started to occur. Sounds like a problem with the boiler not modulating, could be several things, sensors, gas pressures etc. Hard copies of service and installation manuals...

Well the good thing is the boiler is responding to the call for heat and hot water so your pump and fan is running, are the parts that they are operating working though? speak to the engineer ask if he checked the venturi and air pressure switch, if the switch hadn't made typically the boiler...

The domestic diaphragm is sat inside the domestic manifold, it's a brass section that's held with 6 screws. It's 9/10 the likely issue for tap turned on and not activating the boiler. The chances are its slightly ripped round the seems or bellied, either way replacing it wood be a cheap and...

Make : Candy Model : Aquaviva 1100 Problem : When turning on the washing machine to run on number 4 which is non fast coloureds on 30 degree, the machine lets water in to the wheel inside but the wheel does not spin it sounds as if its trying to and the dial turns to complete its program...

Drain the boiler, foot pump onto shredder on expansion vessel pump in 1bar or just under and open up prv again does pressure on exp vessel drop if so its waterlogged and usually draining it completly and refilling with air does the trick.

Nothings more annoying than when i constantly tell me friends im a gas engineer, and when we meet new people they say im a plumber it just doesnt sound as good :P.

well i suggest you go back to basics with the boiler as now you seem out of control of understanding the boilers fault. Do all basic checks on the boiler. These are a must check. 1. Polarity check, gr/bl = 0v, br/bl = 240v, gr/br = 240v, obvious check but if you're not gaining the...

Sticky gas valve possibly check your inlet working pressure at the boiler, note the difference from when it intermittently fires to when it stays fired, gas valve may be sluggish, also check the voltage sent to the gas valve is adequate.