Search results

  1. C

    Bosch Dishwasher SRS43C22GB/04 some expert help please?

    I have just fitted a replacement main circulation pump to the above slimline dishwasher (previous motor allegedly seized) and although it fills and drains ok as soon as the main pump is activated it only runs for 10sec or so and then stops. Water levels are good. If I open and close the...
  2. C

    BOSCH WASHER DRYER WON'T DRY

    Take the lid off and see if either thermostat has triggered. you will see the condenser unit on top of the drum-fan housing back right, thermostats middle front. I think there are two elements on this model. -you can also check the resistance on these with a meter to see of they are o/c ie...
  3. C

    wf541 dismantling

    Have you checked the continuity on the pressure switch with a meter ie if it clicks you should get a closure on the contact pairs? It could be a fault with the control board.......not the switch
  4. C

    Repairing the catch on Neff dishwasher

    Replacement latch is p/n 187185 and is listed at £1.39 on the Neff support site no doubt plus the dreaded and postage........ https://www.neff-eshop.com/eshop%28bD1lbiZjPTA2MA==%29/neff/gb/prodp.htm?prod=S5443X2UK%2f01&ESHOPTYPE=A It is likely held in place by lugs in the casing which will...
  5. C

    Bosch MAXX washing machine

    It is fairly easy as you can get a socket on the mounting bolts through the back and then withdraw the motor from underneath (with the machine tipped forward) For an engineer its much quicker as he only has to remove the one screw rather than a dozen to do the same thing......
  6. C

    Bosch MAXX washing machine

    This has the tear drop shaped access panel at the rear. One Torx screw at the 6 o'clock position and you are in........
  7. C

    Bosch MAXX washing machine

    You need to remove the rear panel-prob about a dozen or so Torx screws (T20/T25) Usually 2 either side centrally are larger ones. Easier to get at the motor if you lean the machine against the kitchen unit at 45 degrees. Remove belt Remove the two 12mm motor supporting bolts Remove...
  8. C

    Carbon motor brushes

    I have replaced a few of these -cut the old one and solder the new one. Watch out though f the armature is damaged in any way it will wear the new brushes away in a few days and back to square one.....
  9. C

    Water retained in Bosch washing machine after draining.

    You can some help on schematics from the Bosch support site https://www.bosch-eshop.com/eshop/bosch/gb/prodp.htm?prod=WFX3268GB/23 Model code can be enetered in the top right search box to your problem You may have a partially blocked tube to the pressure switch which would cause...
  10. C

    Bosch WFF2000GB/12 Tripping mains

    Just an update to say that I have fixed the problem at last! On closer investigation I discovered that the vent pipe that runs from the antisyphon drain chamber back to the soap box was leaking. Overflow only happens when the pump is running at its fastest so any water ends back in the...
  11. C

    Bosch WFF2000GB/12 Tripping mains

    Leccy thanks very much for your input. I have investigated some more using the Megger I have. Applying 500V and monitoring at the plug I have noticed that with the motor disconnected and everything in or out of line apart from the motor gives >3GOhm. With the motor in line and then...
  12. C

    Bosch WFF2000GB/12 Tripping mains

    Thanks for the reply. The last thing I tried was swapping the motor and then starting a cold wash. The dials clicked round,then the door light,then the drain pump had a go for for a few seconds and then it tripped. I think it is tripping as soon as the motor starts to turn the drum...
  13. C

    Bosch WFF2000GB/12 Tripping mains

    Hi I have been trying to fix a WFF2000 which had a faulty element. The machine would previously wash,drain and rinse etc but would abort all wash programs before rinsing with the prewash light flashing twice. The element was O/C so I have replaced it with a new one and thought job done...
  14. C

    NEFF Dishwasher spray arm trickle

    The picture shows the gunge in the top of the matrix which is a result of occasional overflow from the waste outlet and has little to do with your issues. A nice warm humid environment for all kinds moulds to develop.... If it drains out then your problem is lack of flow through the...
  15. C

    bosch dishwaser sg43t52gb water not filling up

    Does the machine reset and pump out water? If it resets and then doesnt fill then you either have a failed inlet water valve (rare) jug impellor(common) or a clogged up pressure chamber and transfer pipe(very common) Can you hear a humming as soon as the machine is switched on? If so...
  16. C

    Bosch dishwasher starts then stops.

    Most common problem with Bosch is clogged pressure chamber and transfer pipe to sump Take the lid,side and bottom kick plates off,then a strip down of the pressure chamber front lhs and remove transfer pipe. A good clean usually gets them going if you havent a valve or switch problem.
  17. C

    exxcel 1400 wahing machine

    There will be something lying across the filter (money? lollipop stick,cotton wool bud etc) so it is effectively jammed. You will need to remove the pump. Its pretty straightforward. Remove lower kick plate -one screw near the front next to the filter and the panel slides to the left...
  18. C

    bosch dishwasher not draining

    Does the impellor flick round in 1/4 turn jerks as this is how it should behave. You can remove the pump but it isnt that easy. You will need to remove the bottom kick plate and metal coverplate usually the wiring harness plastic holder clips on the edge(left side)and should be prised...
  19. C

    Bosch Dishwasher SGS55CO2GB , any help much appreciated...

    check water light can be the flood switch activated in the base or inlet blockage etc you need to remove the lid and lhs side panel(to check for leaks rhs panel also).Remove lower kick plate and metal plate that runs along the front. you will see water matrix and pressure chamber...
  20. C

    Bosch Dishwasher SGS55CO2GB , any help much appreciated...

    You could have a flow problem which if too low will shut the heater off. If you havent done so already clean the pressure chamber and lower transfer pipe to the sump. If it is all gunged up restricting flow then that may be the solution.
Back
Top