Search results

Hi - Many thanx to all and thanx especially for the prompt response

HELP - ERROR 119 Baxi Boiler loses pressure on average every two weeks. 15 times in last 32 weeks - please advise regards

Hi central heating boiler came on whilst timer room thermo was set to off. Renewed batteries in room thermo. Seemed to sync tried it for a few mins seemed to work. Turned it to off. After awhile came on again - seems that I cant turn the heating off - please advise

thanx for prompt supply

I have a baxi duo-tec combi 40 he boiler - My shower unit has packed in. Until I get a replacement my wife had gone to B & Q and purchased a white push on shower with tap adaptors, to use temporarily. On the instructions it says DO NOT USE WITH HIGH PRESSURE SYSTEMS eg COMBINATION boilers or...

:shock: Hi Replacing a rotten timber window with new pvcu type - Using stud framing beneath for pvcu shiplap cladding - the sole plate has to sit on a 5/8 inch high water bar. Any idea how to cut a channel/groove along the length of the sole plate to accommodate the water bar without...

:oops: Repressuring Baxi Duo-tec Combi 40 HE a Heating was not working ERROR 119 Pressure was below 0.5 bar I opened the filling loop The pressure did not alter I tapped the loop checking the connector levers Went upto 3.5 bar and should only be 1.5 bar I closed the filling loop...

:D Hi - many thanx for prompt response regards

:( Hi - Turned off the power feed switch (situated in cupboard next to bathroom) 45AX 250v ac.only DOUBLEPOLE - XM 17039-2 The next day I turned the switch back on and the warning light blew throwing its mains unit switch to off. Checking the cable from the mains unit to the cupboard I get a...

:oops: Hi Not quite certain what you mean Should I be connecting the two (red + Black) leads that are not connected to the red and black connections on the reed unit to complete the circuit. Also I have a pir in this location - so to prove if this reed is faulty if i disconnect all and wire...

:oops: Hi - Have fault showing up on alarm panel - noticed the magnetic reed on front door - cabling appeared slack - took it off The cable is 4 core - black red blue and yellow - the cable going in are all connected to 4 of the 5 available connections on the reed the cable going out to the...

:( Hi Looks Like the bairn (bless Him) has spilt coffee or something similar on the vertical blinds Tried Vanish - did not work anyone any other ideas regards :oops:

:oops: Hi Insulating A few MDF board Doors in an Attic Need to know the best 'stickum' to adhere polystyrene sheets to the door face any advice gratefully received regards :roll:

:oops: Hi Insulating A few MDF board Doors in an Attic Need to know the best 'stickum' to adhere polystyrene sheets to the door face any advice gratefully received regards :roll:

:? Hi Have an extremely cold bedroom above the garage extension. Any advice on how to insulate this ceiling/floor would be greatly appreciated - just bought the house last year and just reallised there is no insulation in this position regards :P

:oops: Hi What options are there for cutting recessed concealed hinge holes in mdf board when making cupboard doors Just using a vrtical drill or would a plunge router do it 35mm diametrr hole 11mm deep in mdf board please advise :roll:

:( Hi to JasonB having a problem locating 16 x 3.6 concealed hinge screws I have located : Concealed hinge Screw 6 x 16mm Did you mean these or do you mean 16mm long and 3.6mm thick screws to suit mdf board or should it be these non tapered chubby screws Also the doors will fit...

Way to go JasonB Many thanx for the prompt response regards :P

:roll: Hi Intending to use 18mm mdf board to form 3 no. 4' x 2' doors in the loft. can anyone advise on what hinges should be used. i've sized up the doors and these doors feel 'heavy' The doors will be 'hinged' to 4 x 2 (inches) uprights need to know hinge type screw type/length...