Search results

OK, NG chap came out last night at 6pm to look - "oh, yes. I see what you mean". He looked at the meter in the hall (roughly in line with the pipe) - "ah, I see a service head adapter. That means your gas is piped with yellow pipe, which is a good thing. It's probable they've used the old...

Cheers all - NG are sending someone out between 4.15 and 8.15 tonight to give it a checkover. I'll be enquiring about moving the thing, or getting it out of the way somehow if poss - it'd be nice to be able to get a car up there and get both on the drive! As it stands, by the looks of google...

Not sure if this is the right place, BUT.. I live in a 50's wimpey house - gas comes in to the meter under the stairs. All is fine. However, outside, roughly in line with the meter there's a tube, sticking up through the gravel. Roughly an inch or so diameter, short, cap of some sort...

I have 2 questions really, I suppose. I have clay soil - every winter, my back lawn turns from grass, to mud/moss, and water. Very slippy, very annoying. I've been in contact with a grass company who've suggested a mix that should do well in the conditions, but we have rabbits...

I own a 50's era Wimpey No-Fines 2 bed house, and I have..well, a couple of questions..heh. First one - in the living room, the ceiling has been wallpapered over - a LONG time past, if the uncovered brown, cracking, crumbling paper is any judge. The paper has been gloss painted, but it has a...

I think you're right - the fire is piezo ignition. Ours can be a pain in the arse - if you click it and it fires, then you accidentally release it before the thermocouple is ready, it makes you wait and wait before it allows a relight. I would be surprised if it allowed a gas stream without...

We built a catrun a while ago, using prefabricated dog run galvanised mesh panels from here: http://www.doghealth.co.uk/ All bolt together, 6ft high panels. They even do a prefabricated door panel. If you were going to do a dual level job, it'd be a case of drilling a couple of new...

Ah, good. That's reassuring then. It's just that the PO had an interesting way of doing DIY. For instance, installing light switches upside down, and not fitting the wire retaining screws, leaving the wires just pushed into place. Or having the entire utility (6 sockets, a PIR and 2...

Last night, I knocked off our immersion at the fuseboard. It was either that, or try to fight the airing cupboard door, which was installed handle-less by the last owner, as it binds BADLY on the carpet, with my kids asleep. No contest. The house is a 50's wimpey concrete job, rewired when...

Our house is a '50s era Wimpey No-fines job, with the single skin brick utility out the back, off the kitchen. This is roofed with the corrugated Asbestos sheet (is that right? Grey, fibrous, quite old, original). At some point (I assume) this has been taken right up to the house and...

//www.diynot.com/forums/plumbing/honeywell-st699b-replacement-battery.294798/#2155342 That's the info for the battery.. :)

Agreed. Same system here (Bermuda and ST699) - check in your airing cupboard - that's where mine was. 3 amp fuse - if it goes, you lose boiler control and your display will act like that. You also have a flat backup battery in the ST699.. :) I had to open mine up and replace it (few quid)...

That's odd. I have a digistat+3, and it doesn't have that issue. Set temps are reached and held fine. :)

I had a honeywell stat and an ST699 hot water/heating programmer, and the 'stat died. So I fitted a Drayton Digistat +3 in is place, and now have the heating on the ST699 set to "on" permanently, so the digistat takes that role over. Works well. :mrgreen:

I live in a Wimpey No-fines house that had the external insulating render, a rewire and double glazing fitted in 1997. Now, I know the units are knocking on a bit, and certainly one needs a new hinge, but at night if you fail to draw the curtains fully, theres a hell of a cold draught. One...

I have 2 of these buggers in a box - 2 brand new cartridges and 1 entire valve - any use? Mine failed at the cistern seal, so I had to strip the loo anyway and put a fluidmaster in instead. The new parts I bought from Lunns..heh..so they're what you've looked at. As I say, unused and sat in...

I had this in our old flat. It was the waste length - I merely put a pinhole in the top of the pipe elbow, where it emerged outside the wall to break the vacuum - job done. Being in the top of the pipe and barely visible, it shouldn't let water out at all, as the pipe is never 100% full of water.

We "aquired" with this house a built in candy Dishwasher. Haven't got the model to hand, but it's not massively fancy - integrated jobbie, 55/65 switch on the top edge of the door, along with a rotary programme selector. I'd guess at around 1997 vintage, as I know it had a new kitchen at...

In our house, we have a Homebase "Nautilus" bathroom suite. I'm sure it's the Nautilus. Anyway, it's become obsolete at B&Q. No problems with it bar the bog from hell - leaking CC donuts, knackered drop valve etc. It's all fine and dandy at the mo, bar a light crack in the pan base which...

I whipped mine out as it was VERY ruddy noisy, and replaced it with a round ceiling mounted PIR. All you get is a very quiet click, and no more hunting for the damn cord in the dark.. :D