Search results

Thank you for the reply. Is there an easy way to check the error lights for the error code to be more sure ? - Otherwise I will try and contact Hotpoint on Monday. Thanks again

Also here is the video showing the flashing lights. https://streamable.com/ttot5h

We had a problem with our Hotpoint Aquarius WDL540P.UK.C and it turned out to be a faulty motor. - It wasn't turning. This has now been replaced and for the first time in a while the machine has started going through the cycles. However, after a while we looked at the machine and now we have...

The timer isn't used - The boiler is on a thermostat with separate settings.

Thanks for the replies so far. Just to confirm, yes it is a condensing boiler.

Thanks for your reply. Definitely have gas. As I say it ignites and stays on for around 5 seconds before going off. It then attempts several times - with it igniting each time. All the noises seem to be as usual. Don't want to spend too much money on it - Especially if the likely fault is...

I have a Heatline Vizo 24 Combi Boiler which has been running OK until a week or so ago. Initially the hot water stopped, and when checking the boiler there were no flames, but also no warning lights. The next day it was fine - was even able to run a full bath without issue. A day or so ago...

Just an update. Now the drum isn't even turning at all :(

Thanks for your reply. That was my thoughts, but I was thinking it might just be something simple - like the carbon brushes or element. Worth a shot first before scrapping it if anyone has any ideas.

We are having problems with our Hotpoint Aquarius WDL540P washer dryer. It will power on without any warning lights. We can select the programme, and start. It starts to fill with water and the drum starts turning. After a very short time it stops turning and nothing then happens at all...

Over the last few days we are having problems with the boiler cutting out after a few minutes. Hot water seems to be fine (although it may be taking a bit longer than normal to heat up), and the flames are all lit. They remain lit whilst the hot water is running (which is correct). The...

Thank you very much for all the replies - Gives me a few things to try. Check fuse in main control panel, replace battery. Am I correct in thinking it is a 12V 2.2Ah battery that I need to go for ?

Thank you - With the bad weather recently I think there has been a power outage, so that might explain it. I'll try disconnecting the battery, mains to reset it first - Does anyone know if this will completely reset the system though (access codes, zone information, etc) and need to be set up...

Could a faulty battery cause the keypad to light up (The power light) but have a blank display and not respond to button presses ? - Even if there is mains power to it ? Is there a battery in the keypad or just the main control unit ? Thanks in advance

We have an alarm system set up with a single Honeywell Accenta Gen 4 LCD keypad. This has been working well for several years. Today we came to disarm the alarm and when trying to enter the PIN nothing happened and the display was completely blank. The power light however was lit up red so...

Thank you once again for your help - It turns out the hose was in fact blocked. We have now unblocked it. (It was blocked at the far end away from the vessel). For future reference does anyone know the name of this hose and the part number incase it turns out it needs to be replaced ...

We have also replaced the expansion vessel with an external one, and again after the system is on for less than 10 minutes, the pressure goes from 1.5 bar to 3 bar. What we have found out is the following..... What does the flexible hose that goes to the expansion vessel actually go to ? -...

We have checked the communication hose and it seems to be fine (from what we can tell). We have also replaced the expansion vessel with an external one, and again after the system is on for less than 10 minutes, the pressure goes from 1.5 bar to 3 bar. Any other ideas ? :( Thanks Daniel

Hi, We have followed the instructions on //www.diynot.com/wiki/plumbing:faq:faq7 to the letter. There was no water coming out of the valve, and also checked the hose - which appeared to be clear. Unfortunately the problem still remains :( Any other ideas/tests we can do ...

Thank you very much for your reply. I've read through the page //www.diynot.com/wiki/plumbing:faq:faq7 and the big thing we seem to have missed is the fact we need to leave the radiator valve open when doing this. If after following this to the letter the problem still exists, is the...