Search results

  1. M

    Texecom Premier Elite 24 With Texe App

    Thanks very much - that's another thing sorted - much appreciated
  2. M

    Texecom Premier Elite 24 With Texe App

    I have a new phone and want to enable the Texe app on it. If I generate a code from the keypad using the same account as on my old phone, will it disable the app on my old phone? Thanks
  3. M

    Mounting Surface Magnetic Contact

    Thanks both for your prompt responses. I have amended the picture to show the architrave as aluminium. Fitting on the top edge: the horizontal edge and vertical are both 2mm aluminium. Fitting on the architrave could be an option, would it be acceptable to do this with a magnetic...
  4. M

    Mounting Surface Magnetic Contact

    I want to fit surface magnetic contact onto an aluminium window in our rented property. The aluminium frame is about 2mm thick at the point where one of the components need to be fitted. Screwing it with other than 2mm long screw will mean the sliding pane will not open. I have...
  5. M

    Fixing Plasterboard to Sheet Insulation Boards

    Thanks Roy C I have not done any exact costings, but the last time I looked at the cost of the insulating boards with plasterboard bonded to the, they seemed very expensive compared to just a sheet of plasterboard and a sheet of insulation. I guess I did not factor into the price the...
  6. M

    Fixing Plasterboard to Sheet Insulation Boards

    Hi I am not sure whether this is the correct forum, if I am wrong I would like to apologise first. I want to the line the inside walls of a room with Kingspan/Cellotex or similar. In the past I have battened the room with 2x2 then infilled the spaces and plasterboarded the walls. Is...
  7. M

    EOL In Series

    Thanks I understand your point about the cumulative value of the resistors. I have just found this in the manual, I think I will try a mock up like you suggest and see what happens. Thanks everyone.
  8. M

    EOL In Series

    The scenario I have is a laundry room with one PIR fitted working configured EOL. There is a two pane sliding window in the room and my concern is the window can be left open when the alarm is set. So my idea is to put two magnet surface contacts on the window, one on each opener. But...
  9. M

    EOL In Series

    Thanks So if I re jig the wiring as in this diagram and place a 2k2 resistor in series. Will this be ok?
  10. M

    EOL In Series

    Hi I have a zone with one PIR fitted. Jumper inside the PIR are set to 4k7 and 2k2. I l would like to fit two magnetic contacts to the zone but unsure how to wire them. Each magnetic contact would have a 4k7 resistor wired across the reed sensor. Where does the 2k2 resistor if the...
  11. M

    Texecom SmartKey

    I found some info on page 112 of INS176-10 of Installation Manual Premier Elite Series
  12. M

    Texecom SmartKey

    Hello everyone I am about to configure my SmartKey but unsure on the procedure. All other Ricochet devices have been installed and working. Do I go into Ricochet learn and then get the panel to recognise the SmartKey. How do you get the SmartKey to send the learn signal to the panel?
  13. M

    Basic Questions

    What I am looking for is to be able to set the alarm so that in the event of it actuating it does not activate the external sounder. I am not confident that I have configured properly and tested it thoroughly to be able to set it and go away on holiday for a month. As long as the...
  14. M

    Basic Questions

    Apologies. Should have Texecom 24 Wireless
  15. M

    Basic Questions

    Sorry is these should be common sense but I do like to check. If the alarm is set in 'Silent Arm' mode, if a zone is triggered it will alarm but the internal sounder or the external sounder will not go off? Once telephone numbers have been programmed in, in the event of ANY alarm the...
  16. M

    No RF Signal

    Thanks for the speedy response. I don't have a expander just a keypad. Oh do I wish I had bought com-USB instead of having to wait. Seriously bad mistake not ordering immediatly.
  17. M

    No RF Signal

    I finished the installation of my system. Awaiting com-USB before proceeding. I registered the Ricochet devices all appeared well. I then left everything powered off overnight - battery out. Powered it back on, 2 devices, one a PIR and the other is a door senor seem to have problems...
  18. M

    Texecom Door Sensor

    What type of tradesman? I am an electrician not an alarm installer. I do find it very interesting, and never appreciated how much alarms had progressed.
  19. M

    Texecom Door Sensor

    On the instruction leaflet it quote Non-Ferrous Mounting Material •Maximum Break = 30mm •Minimum Make = 15mm Ferrous Mounting Material •Maximum Break = 15mm •Minimum Make = 5mm Please can someone give guidance on what these figures mean - are these the gap between the sensor and reed...
  20. M

    Texecom Door Sensor

    I am beginning to realise this. I am an electrician but not an alarm engineer over the year I have installed about 6 alarms - 6 wires - this technology is new to me. But impressed with the system and the quality of the responses on this forum is unbelievable. Its only because of the people...
Back
Top