Search results

yes its faster with the plug out and the brake is free

well went for it and stripped it and cleaned all parts not to bad really ,i did reasemble and try and noticed the gear wantt rising afterwards :(GREAT but undone the outer casing and rotated 180 degrees which solved that .It works slighty better so pleased ,but i do feel the motor magnets may be...

hi lostinthelight ive uploaded some pics of my starter also a clip on youtube just so you can see my issue like i said it turns over just . im sure it shouldnt struggle though as the battrey is a 5.5amp new one also tested the wires and its shhowing 12.8v at the starter with the wires removed...

I'll post some pics up later as I'll pop it off and do some pics the wiring goes via a limited switch for the flywheel brake I did bypass all that and put power direct to the starter and it was the same so guessing it must be the starter .it does work just not like new if you know what I mean...

I'll check power when cranking today but there not a solenoid that I can see on mine unless it's internal in the starter just look a y loom from the battrey to the switch to the starter.was just worries about opening it just in case I can't get the brushes back on the motor ,suppose I could...

Hi again guys just wondering.if anyone has manage to rebuild a starter motor as mine a bit lazy on turning over .Ive fitted a new battrey and checked the valve clearances and all terminals so it has to be the starter, it has the rm65 engine so spares are sparse and was wondering if anyone know...

well today ive removed the flywheel and all is good there no broken keyway :) also tryed the mower with a charged power pack and it seems to turn over slowly but did go so ordered a new 5.5 ah battrey so will check power when turning over then .is there a charge circuirt on the mower then...

Cheers for your help john I'll give Ghs a bell today to see if they can help on the tiny o rings and I'll pop the carb out today to pop a pick up of the part I mean , when I first got it going it was running very high and found this plastic jet blocked and the oring perished but it a lot...

ill measure the battrey tommorrow ,it is smaller looking to what should fit in the bay but even after a charge to 12.8v its the same when starting ,ive also tryed turning it over connectted to a power pack jump starter which was also the same.With overall condition of the mower id say its...

hi john use a alloy hammer :0 crude but did the job and now runs true ,thought it was worth a shot after watching a couple of red necks do it on youtube and thought id risk the 30 pounds which i payed for the mower . only issue really now with the mower is the ticking over has a slight hunt to...

do you have the number for the service link people as im after the valve clearence on a rm65 engine

one other thing on the idle jet which is he plastic piece under the idle screw i did have a couple of splits orings which was the fault of the high reving when i got it going but managed to grind a couple of orings down to get me by does anyone know where i could purchase these from

Hi ive just brought a non runner mountfield which looks very clean ,ive managed to fix most the issues inc bent crankshaft carb strip ,new plug oil and blade and and got it running but just not perfect yet as the high and low throttle isnt really doing it ,as the crankshaft was bent i suspect...

thankyou for your quick reply

Hi guys currently finishing of my front house canopy and have ordered 6 spotlights and a recessed pir and after some advise is possible on the wiring .I would like the spotlights to work as a normal pir setting but also the option to switch them on permenant if i so wish ,i have a switched live...

thankyou for that sketch as its a different one from one i was going to use i was going to order 6x2 to do all the framework pole plate ,rafter, perlin and joist pole but from what i can see you would use 4x2 and a 7x2 for the perlin .Which does make sense now as the strengh need to be on the...

Hi guys ive wanted this for a long time but having to do the neibours aswell aways put me off ,anyhow as he now longer can be bothered im going ahead with it .ill be copying the design from someones down the road and was wondering what size timber to order ,i was thinking all 6x2 but concerned...

that would be ok to be honest as my parent are now both in there seventys and want a downstair toilet fitting were the meter sits like in my house he would be happy if was around a thousand

cheers for that ive just gave him the number for national grid ,one other thing the estates gas was redone in plastic where his is still the rusty steel coming through the concrete floor would you say the pipe is due for an upgrade anyway

hi guys im asking for my father whos gas meter is located under the stairs in the pantry ,he would like it relocated into the garage which is on the side of the property but it will need a new main moled under the driveway into the garage does anyone have an idea of cost and who he would need to...