Search results

thanks a lot for the help.

Thanks for the help, true about the paint it's not been well applied really. Think I'll paper.

Problem is even with them twisted round, (and that's no easy task) so the open end of the U is pointing down they still won't pull up over the pipe! The diameter is too big for the opening to pass over the radiator pipe. I can't pull them out as they foul on the thermostatic valve. I've got them...

Can anyone identify these fittings for the radiator end panels and how do they work? Do they pull off, Twist off or do you need a tool to remove them. They are driving me mad can't seem to get them off or on easily to decorate. Thanks

Hi looks like someone has painted thick paint on new plaster (Photo) I've stripped paper off and it's left this mess. It's in a prominent place above fireplace and dotted around the room. However the plaster is a good finish and I would prefer to paint rather than paper. How can I blend / fill...

I have these black / grey either slate or granite slabs laid in the garden by previous owner. They are 80x20 cm not sure what the material is slate or granite but I'm pretty certain it's non porous. They have come loose from the wall as you can see. How can I attach them? I have looked up and...

It was working fine when I went out. Came back and it was not working. No one was in or working on anything. Thanks for your help but I will get an electrician it's more complicated than I thought.

Harry B. It's these: https://www.ebay.co.uk/mye/myebay/rvi?_trkparms=pageci%3A0b9f1986-56b8-11ec-8419-ca8cc65fa2d6%7Cparentrq%3A90bdd9f517d0a7448527f7d5fff934ec%7Ciid%3A1 Proteus Geyer S20B. It looks pretty old and there is no 'top part' as far I can see so I think it's a MCB.

That's a good idea much simpler, so if the other circuit doesn't work I know it's the RCB.

Even if I turn off the main switch to the consumer unit?

Hi The electrics have gone to my garage. It has it's own mini consumer unit with a 6 amp and a 16 amp circuit breaker. When I presss the test button nothing happens so I presume there is no power getting to it at all. All the house electrics are working except this. It runs from a Proteus Geyer...

Thanks that explains your earlier statement about Zone 7 being for the panic alarm. At least I've found it now! Does the key switch the alarm on and off or is it just to prevent the panic alarm from being accidently pressed? Granny

Hi thanks for the reply. Update: I found a little box inside the bedroom cabinet with a key in it. I thought it was for the telephone to lock access. I turned it and a button pops up on the top. I pressed it - the alarm went off!! I couldn't reset it from the main panel but the remote keypad...

Unset light is permanently lit not flashing. There are only 6 detectors there is a PIR in the kitchen where the main panel is located. Zone 7 is not permanently lit it only lights up briefly when I enter my code and the unset light flashes. When I enter my code sometimes the buttons don't work...

Hi I have a Veritas 8 alarm in the house I have moved into. The 'Unset' light is lit. I enter my code and the unset light flashes 7 times and the Zone7 light lights up briefly the goes back to the same state. I have checked and there are only 6 detectors. I think someone may have set Zone 7 at...

Hi Can you overpaint Hammerite smooth with ordinairy trade Black gloss once it is cured? G.

Hi There are two sets of gates. I phoned the guy last night and told him £200 + 2.5ltr CombiColor at around £30. I have been told there is no more than 8 hours involved work for both pairs but I cannot see how anyone can paint themthat quickly!!!! Or maybe I am really Slooooooooooooooooow...

Hi I have been asked to paint these metal gates. Each gate is 6' wide about 5' high there are two sets. They just have the factory undercoat on which is weathering and showing the galvanised through in parts I thought special metal primer on the galvanised areas and then CombiColor paint 2...

Yes it it a garage door and the woodwork been painted over and over. Can you still get gas or parrafin blowtorches? I have used a heat gun before but I found it rather slow and paint stripper costs a fortune and is really messy. Thanks for the advice. G.

Hi I have some rather large Blisters to remove from fairly thick coats of paint and re-paint over. I don't really want to strip or burn the whole lot off. What is the best way to "Fill" the area where the blisters are removed so there is not so much visible difference in the thickness of the...