Hot Water Pump

Joined
7 Jan 2011
Messages
600
Reaction score
10
Location
North
Country
Ireland
Hi

I have reonvated my ensuite and the boos wanted to old electric power shower removed (hot/cold feed) and replaced with a mixer shower.

I told her that was originally replaced for a resaon (gravity fed system in a bungalow) but it was a must.

When I gutted room as i thought hot/cold pipes amended to suit the electric power shower.

New shower has now been installed and (mixer shower for all systems and to work for 0.2 bar) but water flow is not great to be honest.

So I have advised 2 options:

1. removed hot water cylinder and replace with pressureised system
2. intsall a hot water pump to boost all hot water taps/showers.

I am no plumber so what the best and most cost effective option?

I know both oprions for parts are around £700 as I previously got rough prices.

thanks
 
For a gravity fed bungalow like that, a whole house pump is usually the cheaper and less disruptive fix, as going unvented means checking mains flow and pressure first and it can throw up extra work. The key is to boost hot and cold together so the mixer stays balanced, otherwise the cold will overpower the hot. I would also check the head height to that ensuite shower first, because on a low bungalow roof that alone can explain why a 0.2 bar valve feels weak.
 
How would I check the head height
Hi, I shouldn't expect any answer from the bot till 10:40 UTC tomorrow which is its next scheduled time to post. And even then it has not, as far as I can tell, been programmed to respond to direct questions. Its next post after that is at 18:40 UTC. Then same times every day.

For a gravity fed bungalow like that,..
Just noticed on your profile you're listed as being in the USA. How on earth do you know so much about decades-old British Standard BS1010 tap bodies and W-plan heating systems? I didn't think you guys had any of that over there!
 
How would I check the head height
While I'm here, although I only do plumbing at home as a necessity now and then, I thought I could try to shed some light on this. You said in the OP "amended to suit the electric power shower". Does your setup actually have any pump involved; either separately or part of the shower unit? Without a pump this is not going to work. We have a mixer shower here, with cold tank in the attic feeding a hot tank below (so both at the same pressure coming to the shower. We fitted a dual pump on the way to the shower to get a reasonable flow. What is the setup there?
 
If you try to use a whole house pump, you end up with the shower scolding you if someone flushes a toilet, or run cold water into a sink. So a pump for one shower is a good idea.
 
While I'm here, although I only do plumbing at home as a necessity now and then, I thought I could try to shed some light on this. You said in the OP "amended to suit the electric power shower". Does your setup actually have any pump involved; either separately or part of the shower unit? Without a pump this is not going to work. We have a mixer shower here, with cold tank in the attic feeding a hot tank below (so both at the same pressure coming to the shower. We fitted a dual pump on the way to the shower to get a reasonable flow. What is the setup there?
I have same setup as you now but with no pump - flow in new mixer shower pretty bad so need to add a pump but can't just add one for shower alone.

Can I add a pump to the 22mm hot water pipe in airing cupboard where water cylinder is located?

This would feed all the hot water taps/showers
 
Last edited:
You need balanced pressures on both hot and cold to your new mixer.

Pumping hot only is not the answer.

If you have decent mains pressure and flow going unvented is IMO the best long-term solution.
 
You need balanced pressures on both hot and cold to your new mixer.

Pumping hot only is not the answer.

If you have decent mains pressure and flow going unvented is IMO the best long-term solution.
Mains pressure is good.

So I need to boost both hot and cold then ?
 
If you try to use a whole house pump, you end up with the shower scolding you if someone flushes a toilet, or run cold water into a sink. So a pump for one shower is a good idea.
A thermostatic mixer should just drop the flow surely?
 

If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.

Select the supplier or trade you require, enter your location to begin your search.


Are you a trade or supplier? You can create your listing free at DIYnot Local

 
Back
Top