Recent content by Andy_2504

  1. A

    Drayton miGenie programmer

    So I've done some more monitoring and I now believe this isn't simply a random event but the TPI setting turning the boiler on and off for around 1 minute at 10 minute intervals per hour as it is set to a max of 6 cycles. I'm assuming this is due to the set point temperature being reached and...
  2. A

    Drayton miGenie programmer

    Good morning. I've recently changed the setting on my meGenie programmer from auto to manual and I've noticed the green light on the programmer will randomly come on and fire the boiler up for about 30 seconds when the thermostat isn't calling for any heat. I did wonder if a factory reset may...
  3. A

    Odyssey-W Sounder

    Turns out the problem was caused by the panel software being older than that required by the sounder. Once the panel had been flashed with the most recent software and the sounder re-learned all is working as expected.
  4. A

    Texecom Connect SmartCom

    To update on this, finally flashed the panel and can't thank secureiam enough for the assistance with this. Turns out that the flasher unit I purchased again from a well know auction site was not an official Texecom unit and as soon as I connected the genuine unit (courtesy of secureiam) it...
  5. A

    Texecom Connect SmartCom

    Cheers, are you around a little later as just up the shop with my daughter but will be back in about 40mins and then free or another day?
  6. A

    Texecom Connect SmartCom

    Unfortunately I'm based in Durham but that's a very kind offer. I've put the front back on the panel now but could maybe have a stab at it another day. I tried my pc and have also since tried a lap top but again the same problem with the software and COM Port not showing.
  7. A

    Texecom Connect SmartCom

    I think I may have to admit defeat with flashing the panel and get a professional in. I received the cable flashing interface this morning but can't get the flashing software to list the COM Port. I know which COM Port it is as I've have the pc connected to the panel with Wintex without any...
  8. A

    Odyssey-W Sounder

    Hi All, looking for some advice on this sounder if any one is able to help. I've connected it to the system although once I logged off the engineer is immediately activated. It seemed to have connected correctly as per the LED's and it's showing in the Ricochet Monitor. Initially when it...
  9. A

    Texecom Connect SmartCom

    That is true but I've now had it nearly 5 months so should of checked earlier. I've also been connecting a couple of ricochet pir's but for some reason one of them is constantly showing as Active in Wintex and in Alarm in the Ricochet monitor, never seems to change to secure but not sure why?
  10. A

    Texecom Connect SmartCom

    Didn't specifically mention it, lesson learned! I'll have to get a flash interface
  11. A

    Texecom Connect SmartCom

    It says V2.09
  12. A

    Texecom Connect SmartCom

    I'm not sure but I'm assuming that wintex would show the correct version. Would wintex not show the Smartcom option if the panel doesn't meet the requirements? This may be the joys of purchasing the panel from a well know auction site where it was advertised as new!
  13. A

    Texecom Connect SmartCom

    That may well be the problems then, it's an elite panel but just noticed Wintex says the panel version 2.09 but the box says V5 so I'm assuming I'm going to have to flash the panel although I'll need to purchase a lead first
  14. A

    Texecom Connect SmartCom

    It says Version 7.2, Build 3.1
  15. A

    Texecom Connect SmartCom

    I'm digging up my old thread here but I've only just got around to changing it all over and installing the SmartCom:rolleyes: the problem I'm having is that the instructions say to set Com Port 1 as SmartCom and Com Port 2 as ComIP although there doesn't seem to be a SmartCom option to select...
Back
Top