Search results

yeah. totally used to work and nothing has changed around the house or anything. they were unused batteries but i have had them a while. do you think its worth trying a litterally new purchased set? i'll give the frequency change a go tonight and post back if it fails still. thanks

hi guys. thanks for the quick replies. no idea if i've got motorized valvesto be honest. my assumption was that as stem said, it seems like the receive just isn't getting the signal. that being said, it does work if i move the thermostat right next to the receiver! do you think it...

Hi all. To control the central heating on my vokera combi, i was have a horstmann T50 wireless thermostat and receiver ( i think it might also be known as a HRFS1). All of a suddan, the thermostat does not now switch the heating off. It will kick the heating on no problem (on a program or...

Hi It's not a frost free freezer and generally seems to fine most if the time. I've been doing a bit of experimenting with it and aha seems to happen is that when the alarm goes off, it sounds for about 8 iterations and then goes off. So I'm a little stumped, it. Detail doesn't appear...

Thanks for the reply. It's an I desist freezer only. So I guess the same question still applies really. Could it be the thermostat? Thanks

Hi all. Over the last few days my freezer alarm has been going off and the only way to stop it is just hit the fast freeze button and leave it on. Anyone know why it would do this? The door is certainly closed properly. Could it be an issue with the door seal or maybe the thermostat...

ahh right. thanks for that, now that i look closer i can actually see that the sides of the hole are formed ;-) thanks for for, panic over ;-) cheers

hi all. i wonder if you can clarify something for me. my washer/dryer door seal as a hole in it. the hole is located at 6 o'clock approximately and is actually near enough next to the edge on the drum side of the seal. do i need to bother replacing this or will water getting through this...

Thanks for all the replies. It now seems to be working fine. The mains set up was ok and once i went for the signal brown into the other L and the signal blue in to SL on, its been working fine Thanks for all your help guys, i gues it did require the VF operation after all, although i've...

Thanks for the replies guys. so the consensus is that i need the VF set up then? Judging from your replies, i take it that this means the VF feed is actually the brown feed coming from the boiler? and then the blue into SL on? Just want to get this clear before i attack it again. Thanks

thank for the reply. i assumed i didn't have Volt Free connection because there was nothing special that i could see about the current receiver set up ie just a live/neutral. the diagram relating to the VF set up suggests that i would already have an existing VF feed which i dont think i...

Hi all. Im replacing our existing wireless roomstat/receiver with a new one which also has 5/2 program option (We have a vokera combi boiler) So, i wire it up, switch on and all seems well and good, hot water works fine but as soom as i up the temp to force the heating on (to test the RF...

Hi all. Since fitting a new tap into my kitchen (mixer tap) the cold water just comes out in a jet that spurts water just about everywhere! The hot water is fine. The kitchen tap is the only one affected, bathroom cold/hot are both fine. Any suggestions? Thanks

thanks for the reply, i also have a single in the kitchen that i can change while i'm on, is single pole acceptable throughout the house?

Hi guys I've got to replace a couple of single sockets in my living room and i'm going to replace them with doubles instead. Do all new sockets need to be double poled or is single still fine? Thanks

the socket is an existing socket attached to the wall in the usual fashion. my meaning was whether is was ok to have and access hatch (for want of a better word) in the back of the cupboard to be able to get to the socket?

Thanks JohnD The reason behind my question is that there is already a double socket beneath the worktop and just to the left of where the single oven is going to be located. So i does appear that i'm able to simply plug the oven into and properly lable the socket itself? Thanks

Hi there. I know there seem to have been several post regarding single overns and how to supply them and i note from these that i'm able to simply plug my new single over into a 13a socket (also recommneded in the instructions) My question relates to the location of that socket ie does it...