Search results

Isolate Mains Supply Remove Battery Apply Power back to panel then press the Reset button twice within 5 seconds of powering up the panel this should then default the panel to factory settings. You will have to re programme the panel afterwards Enter Code 0123 tamper light will be on this...

cheers for that. Problem is a 16 ohm extension speaker is too loud, i am wondering do you know where i can get a smaller speaker. The ones that are an the Optima Compacts would be ideal do you know what size they are ?

Hi Guys, Just wondering can you connect a 12 volt buzzer to the speaker terminals of a control panel & would it give entry/exit & alarm tones :?: Thanks

Accenta 8 mini

Hi guys, I need to connect a dialler it can be programmed pos or neg start, however there are no communicator outputs & the bell is a scb connected to the + - terminals in the panel. How would I connect to the dialler ? Does it need a relay ? Cheers. :wink:

Hi Guys, Tested PA through to ARC & it showed PIN 3 in alarm condition. Got an engineer in & it was the actually the communicator that was holding at 0V & not the panel. So dont need a new panel after all. :D All now working fine .

No problem madman Just trying to choose a decent panel would have got a galaxy but not enough room in the cupboard needs a small end station like the accenta mini dimensions. looked at texecom panel too big, Would you suggest any others must have communicator outputs though

I can understand where your coming from madman however if you google accenta G4 installation manual it comes right up so the info is very easy to find Obviously there are other panels where it is very hard to find a engineer manual this info I would not put onto the forum

Thanks for the advice alarm, i did it yesterday. I put a short between the set output & left hand tamper terminal & that defaulted user & eng codes, I down powered whilst doing this and powered back up when i closed all tampers and put user code in it silenced internal speakers but the...

Hi Guys, The other day we had electrical work in the area so they disconnected the power for around 8 hours. The alarm back up battery worked ok untill it died then the SAB kicked in outside Power come back on & i silenced with my code. However the engineer code which was set to default...

National Monitoring

Hi Alarm, Yes its programmed as positive removed. I'm not sure who runs it as i send everything to a admin email address. I think the owner is called David. I Know Northern Monitoring used to use there building but then they relocated to a brand new building down the road

May sound daft but what do you mean by negative rails commoned ? The input is set to negative yes, I just took the wire out if the intruder output these are positive removed and placed in to the bell - trigger, But when i did a bell test it didn't trigger the digi. The make is a sensor...

My work will not change the way the panel works i will just get my discounted price, I did want to connect it to the bell trigger so every time its triggered it would send a channel 3, But it didn't work. I thought it may not have triggered due to the fact there is no bell connected ? The...

its currently connected to National just waiting for renewal date so i can terminate and connect it through to my work Its on my nans house, it has 2 key holders me as one of them. I only live on next street so not far away. On my house i use a keyholding company

Hello, I have a digicom connected to a accenta G4 mini via the communicator outputs When the alarm first triggers it sends a channel 3 like normal, however after the bell time of 3 minutes the systems rearms, I then triggered another detector but it doesn't re trigger the digi this is beacuse...

No not all professionals are bad i just worked for one that was run badly. The response times where bad for the CCTV but the intruder alarm monitoring was always to standard i must give them that I know a few guys that went down the road to work at another ARC & that is bang on, enough...

As for rules & regs that can be inforced, I have seen documents falsified just to keep the assesor from the inspectorate happy. :shock: The company even paid a guy to come in to make sure we where up to the standard ready for the assesment. The guy tried his best like, should have seen his...

We never had access to engineer codes as there was no need for us to know that information. We only did remote resets over the phone, customer would call in we would ask for the number on the panel, i would type into the computer, the computer would then display me a number, they put the...

I can not prove that the engineer code was given out as the only person that can prove that is the enginner looking at the log on the panel. But customers could set & unset the alarm after speaking to engineer. As it would send open & close signals. I assumed if the panel said call alarm co...