Search results

I have just left them covered for 30 minutes and yes when uncovered both that i covered have triggered the alarm showing the 2 zones and 'intruder' but the LEDs don't show up on motion? Is there a minimum time the system has to be set for before the wireless PIRs will cause an 'intruder' signal?

I've setup a few DT8M Wireless PIRs as a quick temp fix before installing some hard wired detectors. Inserted the batteries, all configured as a zone, signal strengh good, walk test working fine, set the system, moved a bit , lit up and set off intruder alarm. However, i left the system idle...

Hi This is going to be very simple for someone to resolve, however i've fitted a direct mount RF module inside my Flex Control Panel. However i cannot exit engineering mode due to RF Tamper I cannot find anywhere in the manual or leaflet how to disable the tamper for the module, seeing as it...

Will a pyronix deltadell WE (wireless version) work with a honeywell galaxy RF portal c079-2 ? the specs say it uses the same frequency. i've hardwired a deltabell to panel before, but with cabling constraints would the wireless version work with the honeywell portal?

I have connected the ALARM out on a Hikvision NVR to a Galaxy Panel Zone using 2 core cable and programmed the zone as 'INTRUDER' I've set line crossing and done a manual test and the alarm is activated however the log (when clear the alarm) shows as a TAMPER Not INTRUDER. I've fitted a 1K...

I self installed a G2-12 system about 10 years ago when moved into house, its been absolutely flawless and no issues with both wired and wireless devices, I'm moving home which again property doesnt have an alarm system so will be looking to install. Currently, I have the G2 with LCE ethernet...

Definitely not the zone (device) battery issue despite coming up - i replaced all wireless devices with fresh new batteries!

whats the difference between the 2 battery events? i love firmware/software testing - whoever wrote it needs to do a better description! lol

If it was blown wouldn't this cause further issues or be permanent as it clears itself after a moment.

No I havent - could it be failing rather than blown?

Hi, Just wondered if anyone can assist. For a while now on my Galaxy G2-12 I keep getting alerts approx every 24 hours (which i assume is a self test interval) of: +BAT MIS -BAT MIS -BATTERY +BATTERY I've changed the main backup battery and all batteries in all Wireless devices - PIR, Door...

Yes the model I have doesn't come with EOL resisters included and I think you forgot to attach something ? thanks.

Hi Everyone, I've previously setup an alarm system with honeywell 8ir103 PIRs with the resisters etc. I'm installing another G2 system and the PIRs are end of life so now using IS312 PIRs. Can someone just clarify which terminals on the PIR i use for each of the 2 data cables, and I presume i'll...

Thanks, i just wasn't sure with it being low voltage and very thin cable that it should be ran the same route as all the twin and earth grey cables.

I want to install a 12v dc smart doorbell and run the cabling under floorboards along the joist cable clipped, along with all the twin and earth etc cables. However, am i correct that I cannot run the standard bell wire alongside/near the main 240v twin and earth lighting/socket cables? I might...

Ta! I'm guessing for normal domestic install a power rio wouldn't be necessary although if say have a 50 zone flex with say 10 pirs this would still be under the main panels power capacity.

Thanks I thought that might be the case. I just think logically that if the keypad is connected to a rio and the rio fails the whole system will be down but if keypad wired back to panel the rio can fail and keypad still work. so my plan would be to have main panel in loft, belden cable between...

Is that the only supported configurations a single daisy chain or panel being in the middle. How many lines out can I run from the panel. Just not always possible to locate items as part of the chain and always better to have keypad direct to the panel rather than a rio so that if the rio fails...

I have a galaxy panel which currently has a keypad linked straight to the panel in the loft using all on board zones and an RF portal next to the keypad daisy chained off the keypad. My question is how many data lines can be run off the main pcb from the A B data line if I wanted to add another...

it's this model Hikvision Video Doorbell WiFi model DS-KB6403-WIP