Search results

Hi. The programmer has power, the LCD is displaying the the time and even if you switch it to 'on' (a red light comes on, on the programmer only) the boiler does nothing. Only when the programmer is on, and the boiler is set to C/H does the pump in the boiler start to whirrr. IF the feed to...

Goes to this (pic2) There is a fused spur here, could it be here that has blown? The immersion heater switch lights up when you press it (assume this is working still) Thanks Jon

pic 1

Okay so after looking. The boiler has a white mains cable which comes out, and up in to the timer box, which controls when the boiler comes on/off. See photo here: This timer box has power, is on and works. If I switch the boiler to 'central heating mode' so the radiators should warm. The pump...

Thanks! I will have a check! Cheers mate!

Hi Thanks for the reply. Neither of the two lights are lit at all. They are both off. Must be a power issue then, as you mention. May I ask where I find the control panel fuse please?

Hi John, Thank you. I can see no lock out light. This is what I have under the hood of that. Any ideas? the clear box has a button which you can press, tried that - nothing. The boiler has power as the pump runs when you select 'heating for radiator' mode.

Thank you for your help :)

Hi. Thanks. Loafs if oil. No obvious controls on the boiler!! Only used to gas ones I have had previously.

Hi all, This is my first post, I hope you can help me with my Boiler issue. I have an Oil fed worcester-bosch 12/15 Danesmoor boiler, which has stopped heating water. The central heating pump is working fine, so it has power but only that, it does not fire up and heat on either the c/h setting...

Hi :) I've just finished skimming and patching up my bathroom with multifinish (having previously removed all of the old tiles) Can I just tile to this surface or do I need to prep it with PVA or simialr please? Thanks Jon

what would you do then? line of carpet grippert 1/2 inch from where you want the carpet to stop and instruct the monkey from carpetworld or similar to glue it down in that area?

Hi :) Could someone please advise what the best way to do the follow would be: I have a large room which I want to seperate, half carpet and half sanded floor boards. What would be the best way to create a 'strong' divide running down the middle of the room. The length involved is 3.3...

Hi All, Bit of an update on this. I still have the damp problem but have done the following: Had the flashing replaced (over standard) and then inspected by a loss adjuster friend - confirmed its been done well. Had a wood burning stove installed. I've noticed that since unsing...

Do it once, do it properly. :mrgreen: I've no plans to do it again!!! Cost £750 so far for a large block of concrete! :D

Should be tough enough. C35 mix with fibre, on 3 inches of hardcore wacked down and the concrete is 8 inches deep, its for a kennel so It's well overkill. I'm looking to make it last though. So I'm looking to seal it thinking that it will protect the concrete from the dog urine? Good...

Hello, Could someone reccomend me a good concrete sealer please, for a freshly laid slab of concrete. the slb will not be covered and I want to stop the frost/water getting in to it. I've see this http://www.thompsonsweatherproofing.co.uk/products/product.jsp?id=1 Is it any good? +...

Thank you, I never knew concrete was that expensive though! considering its for dogs to wee on.

I don't want it to move :mrgreen: ! I've got some rather large dogs and the kennel needs bolting down to this. renting a concrete pumper seems a huge expense. having the concrete mixed on site seems a huge amount of work having gthe concrete dropped off on the drive seems a huge...

Hi mate, Thanks for the quick reply. The problem I have is the distance from the front of the property to the area. I've had quotes of £440 for a mix and barrow service £300 for a mixer to dump 3.5 metres cubed on the drive (which could be interesting if it sets) them almost £1000...