Search results

Matthew, thanks i hear you its already turned off, i have no intention of using it. I just need to know whats what so i can talk to the installers tomorrow and get them to correct it. thank ewan

its a baumatic BT2710ss 90cm twin cavity Rated Voltage 230 Vac 50Hz Supply Connection 20A double pole switched fused outlet with 3mm contact gap Max Rated output 4.34Kw

All, getting a new kitchen installed at the moment and i have a question. The instalation guide for the cooker i have says it shoudl be wired to a "20A double poled fused spur outlet" However, at present the oven is just connected to what was a everyday plug socket, The cooker has two...

should have said its a combi boiler and I live in Glasgow which i think is a "softish" water area. after finding the FAQ's :) seems like this is a case of "ketteling" but with the addition of the leek does this suggest the heat exchanger is also damaged?

All, I'm hearing a noise when my boiler fires up. The noise is like a *mix* of car brakes screaching and a kettle boiling. Also there is a small leak from the underside of the bolier when its cold, this stops once its been running for a bit. The noise lasts for longer when the bolier...

thanks. i'm a 2nd floor flat and can see no presure release pipe on the outsied wall., all the rads are fine, no weeping. The water is coming out of the bottom of the boiler and its a dirty yellow colour?? which seems weird as if i drian of some liquid from the system via the drian value on...

I have 2 Sanier Duval Thema F's, one does HW one does CH. The CH boiler seems to be leaking a little when its cold, it dumps enough water to drop the pressure by 1/8 of a bar. When the boiler is up and running there are not leaks. Generally both boilers work 100% ok with no other problems. Both...

i've googled till the cows come home and cant find anything. no local plumbers merchants so i was hping to find somthing on line.

all, fitting a new saniflo pump (i know there c*rap but i have no choice) and i need to fit an air admidance valve to a 22mm solvent weld pipe. the only value i can find is a FloPlast value that fits to 32mm. anyone know where i can get a 32->22 reducer or where i can get a value that will...

>first question, why replace? Yeh i think so plumbing and eleectric access over the years have distroyed then it lots of areas. I want a high quailty finish so i'm just going to replace them. I managed to source some good quality boards 28mm think and 137 cover for the job. These are the same...

All, This weekends job is replacing the original T&G floorboards in my 1890's flat with new ones. Any tips and tricks for making this a painless as possible? Any suggestions of specialist tools required for the job? Cheers in advance e

hey Amanda, looks really good. A question for you though, what did you do with the floor, i looks like you just painted the floorboards? in some earlier pictures there looks like there are some gas between the boards, i later pictures these seem to be gone? e

all, i live in a 2nd + 3rd floor victorian flat. the main bathroom on the 2nd floor used to be a bedroom but has been converted at some point in the past. the wc has a saniflo unit. there is approx 2m from the toilet location to the outside wall of the flat, the origional main waste pipe...

found the info i need, chock block and stick on a blanking plate, easy crafty: the new bath thats going in is a free standing roll top so i cant see wet arms hanging over the sides of the bath dripping water + a live socket being a good thing... better ti be safe than dead and all that :)

if cant get access to the wire spur to remove it, look that way at the moment, what else can i do?

look what i found when i removed the old bath from my bathroom, copper pipes in the foreground are the baths hot and cold feed. The horizontal marking above the socket is where the top of the bath used to be. Surely that's not the smartest thing to do! :shock: So my question is...

yep, i can confirm that turning to 0 does close the value of completly, i just took the bu*ger off!!!! First time drainig the down the system, first time taking a rad of, floorboards up and pipes capped of underneith, system re-filled and back up running, all went like clockwork... and i'm...

hey, i have these (see pics) Danfoss TRV's, i cant see the model number anywhere. I want to remove the radiator but how do i know if the TRV is fully closed. Is turning the value to 0 enough for these types of TRV's or do i need the decorators cap etc. tia e