Search results

Hello Turned the isolation switch off on the garage consumer unit for the lighting circuit, 3 outside security lights, fluorescent lighting inside the garage, due to replacing an outside SL bulb and now the light switch in the garage for the fluorescent lights is working the opposite way. Any...

Appreciate your response. The valve assembly is a straight swop, wiring like for like is simple, I have already drained the system three or four times as I have completely gutted and refurbished both the bathrooms and moved the location of old radiators and installed stainless steel towel...

Hi Tony Once again thank you for the swift reply. Appreciate the info about the copper body assembly I will look as the motorised valve does look ok however when I priced them up there isn't a great deal of difference in price from a motorised valve and the complete assembly. Can you confirm...

Thanks Tony My suspicion was the micro switch on the motorised valve, I have already lubricated the shaft of the valve and it did appear to free it up. With regards the combustion chamber I fully appreciate your comments but honestly I watched the guy servicing the boiler and the combustion...

Thanks for getting back to me, interesting point about the motorised valve, as I have a six wired motorised head on 22mm copper pipe, this would suggest then that I have a 28mm motorised head six wired on 22mm copper pipe instead of the five wire. I am a little confused as the (sixth wire...

Hello, Thanks for replying. As you have asked.... I have an intermittent fault with my boiler, it is not firing up in the morning with call for hot water so I had the boiler serviced hoping that may resolve the problem. I have since replaced the combustion chamber seal which was falling apart...

Hello, I need to replace the 2 port motorised valve assembly on my heating system. The current motorised valve has the following id numbers 40003916-001, it is the six wired version, is this a V4043 I need ? I have a heatrae sadia mega flow heating system with a Potterton pro max HE boiler...

Thanks for the reply, so would that be common practice? what would be considered a reasonable charge?

Further. Changed the battery on the diner PIR not getting any full alarm actuations anymore which is a relief however I cannot set the alarm now as the default message says the engineers alarm code is needed. Question is it incumbent for the installer to give you the code if you request it ?

Now sorted thanks eventually found error code in log Low Batt

Just tried removing the zone, first attempt, entered zone 94 pressed 0 message was 'Error try again' Second attempt just entered 94 without the 0 'do you want to set, 'yes' message Error you cant remove that zone.

No spiders or cobwebs, To confirm then to isolate/ remove the diner zone. I enter code, press no until it says remove zone , press yes enter zone 94, press 0 ...do you want to set , press yes.

Hello Thanks for the reply. All I have site record card with Zones 91 through to 98, the diner which is shown as the problem Zone is 94 so would this be zone '4' ?

Hello everyone Inherited the above alarm system it has now actuated twice in the early hours (typical) driving us and the neighbours nuts , shows Diner as the problem I believe it may be the wireless( are they called PIR detectors?) I have tried calling the installer/alarm engineer, not...

Hello, I have a Potterton Promax 24 HE boiler doesn't have any temp control on it, the only temp gauge is on the side of the hot water tank but only has numbers not temperature so I don't know what they relate to or if it is set at the correct temp. Picture of temp gauge shown. I have a Mega...

Water Temp Gauge

Ok cheers should be ok I'm not a bad DIY'er ripped everything out put new plasterboard in and tiled, I did look on youtube and most enclosures seem to be fitted by fitting the channels and building the shower enclosure from there. Thanks as always for the advice (y)

Not sure what you mean about the size, I have one moisture board dot and dab on blockwork so long screws in rawl plugs the other wall is moisture board in metal channels so not sure how I will fix to that probably red rawls pushed into tiles 10mm thick bit of silicone on each channel fix.

Hello everyone, About to fit a Homebase 900x 900 two sided bi- fold door shower enclosure onto a Mira shower tray. The instruction booklet suggests assembling then lifting onto the tray marking up then removing and drilling etc. This would be impossible for one difficult for two and three...

Hello everyone, As the title says would be extremely grateful for some assistance. I have 10mm thick 600x300 ceramic tiles fitted to moisture board and I need to secure the shower cubicle which sits on top of the shower tray to the wall. I was going to use red rawl plugs 6mm drill and push the...