Search results

got to tile 2 sq m of 300 mm x 300 mm sheets with paper backing on front what adhesive to use i obviously dont want adhesive in joint as when i soak &take paper off i want clean lines for jrout any suggestions please

Thanks for help to Alumni &Ticklyt Will have a look in Maplins tommorow Regards Larry

TONY thanks for reply I will ask pumphouse what alarm they recommend &fit one - wont do much good if the house owner is in the Bahamas when it goes off I think the house owner will have to accept some responsibility as it was their decision to have boiler & cylinder fitter in cellar Thanks Larry

Ihave had cat 5 cable installed in all rooms in a house we are upgrading data outlets in all rooms what connectors & where can i get them so as to connect to a virgin modem in cellar six cables in all thanks Larry

Thanks for the reply Looneyfitter I may have to contact Keston for their advise as i also need to deal with the sanicondense if that goes on holiday unexpecdetly Do you think it might be simpler to fit warning if pumps fail ?

I have just purchased a pump house pump ph-5-ol-hdhw to deal with dishcharge from either main pressurised cylinder & heating system safety valve the boiler is a keston c55 system boiler can anybody advise how to connect safety wires on this pump to keston wiring also i have a sanicondense...

where can i buy polyroof 185 for a flat roof progect i am starting many thanks larry

if you contact manufacturer with all the relevant details they will help also they have appointed repairers countrywide hope this helps

It all depends on loading there are limits on how many litres per minute velocity etc you need to make a diagram and work out demands on each circuit i think there may be pipe size calculators on web somewhere there is one for corgis for gas but they cannot agree how to use it

autolycusd if your waste hasnt got overflow spigot & you want to use it you will have to get a bath trap with the overflow facility other possibility is swap it for one that has goy overflow spigot

doormouse1 if its a living room you should put rads on coldest wall under windows if you prefer if rads are on internal wall behind where you sit you will be in line of cold convection & will need to wrap your legs in winter

kate ideally you could have all supplies & valves behind a back panel which is easily removable if you put them under the base acess is not that easy to rectify any future problems

muffking i use hep20 plastic fittings quite a lot depending on routes hidden or not etc etc i do not use them on chrome pipe as hardness of chrome finish stops barbs from biting & making a good joint if the two bits of pipe you are jointing cannot move apart it might be ok

drippybrain ideally you need to isolate pipework in concrete and connect proper pipe test kit pressurise to minimum 4 bar and then you will have a definite answer as to what is occuring on new pipework i usally pressurise to 6 bar for 10 mins usually tells where the carpenter has used pipes...

thanks everybody for your input spoke to heatray sadia today who say any two part valve is acceptable to them have now fitted v4043h as they are readily available everything is now running according to plan

doitall the valve now fitted has malfunctioned firing boiler when programmer not calling for hot water i am aware of implications you refer to

on a honeywell vc4613 two port zone valve in an s plan layout on megaflo mains fed indirect cylinder does anybody have a wiring layout programmer is st699

Kinhell a better option would be toilet pan mounted on a frame purpose built then you can easily alter height to suit ideally a fall of 1;40 is the one to aim for also easy to mop under when it leaks

belboz if you use the PHILMAC coupling you could use a copper end feed fitting to match the bore of lead to act as an insert then no problems with lead pipe collapsing ideally lead should be swapped for mdpe of similar bore

cyberdine use an electric freezer for steel ok as long as you dont have a power cut last one i did on thawing out water everywhere as it was an old seam welded pipe situated on sixt floor always a good idea to have a wet vac handy or waders hope this helps