Search results

Hi Guys, am looking for a shower screen, the max height i have due to the bathroom ceiling slope is 1.3m. Cant find a screen this height, although there was a folding one there when i refurbed the bathroom so they ust exist! Dont care if its one piece or folding, just need to find...

Ok, having seen loads of recent threads on outside taps, rad valves etc........ Whats the weapon of choice? personally after using PTFE for a long time, i wont leave home with 55! much much superior to PTFE with the obvious benefit of being able to 'back off' without leaking. Never had...

I am afraid to say, Yes it is notifiable, they will want to inspect anything to do with waste and drainage, not to bothered about the hot and cold side of the plumbing though. You will also need extractor fans etc on the electrical side, all which needs to be carrried out by a qualified...

Have sent a S****y email to Mira. Thats not a bad idea, will talk to my local merchants and see if they have a tel number for a local rep. thanks

Thoughts on this please gentlemen if you please. Having installed a brand new out of the box expensive Mira Magna EV Pumped shower for a customer last week, it failed to work out of the box! Having fitted many of these in the past, I know that all electric and plumbing was installed over...

Unvented are DIY, you need an installer with the qualification to fit and maintain them.

May as well remove the w/m valve, replace with a backplate elbow and screw tap on, hopefully there will be enough 'flex' in the pipe to screw the backplate elbow to the wall? That way your tap is in your outhouse, is that what you want as you mention not wanting to drill through walls...........

Unvented all the way would be my advice if you have the required flow and pressure rates. You wont regret it.............. Option 2 would prob work out cheaper than option 2 at the moment, I cna buy stainless cylinders cheaper than copper due to the high copper prices. Good luck!

Hi Guys, After a bit of advice please? I need to lay a new screed about 40mm in depth to raise the current floor level in our porch way (we have moved the front door forward so effectively the outside porch is now our hallway floor!) Its only about 2m square in area, but the problem is...

Normally turn the spout so it is running parrallel with the sink, so not facing you, and lift off! Might need quite a pull though as sometimes very stiff. Then just replace the O ring (s) Good luck

Not to mention reseating the tap face if needed :D

Thanks for the help with this one. Have done the IPconfig and ping to printer. Printer IP is 192.168.2.2 which ping is not reaching it. info from dos prompt on both ping and config are Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved...

Hi, Hope someone can help ASAP please!!!!!! Have a Deskjet 3050 wireless printer, which i have tried all ways of installing, but cant get it to print wireless. I have a Compaq laptop with wireless, Belgin Wireless router, I can see the network on the laptop, no probs and thats how i connect to...

Hi Guys, Please can you help before i throw laptop out of the window. I have lost the original install disc for the olympus VN-2100PC and need to get it working on my new laptop which is running Windows 7. I have tried to update drivers etc and load software etc from the olympus site...

Remove stack carefully from top down in sections, and replace in plastic all the way from the plastic fitting at ground level.

Thanks for the help on this Zipper........... I looked at the bottom and rear of fridge for PCb's etc but could not really see anything, I assume the big black thing is a compressor or motor? next to it is a small black box that a couple of cables go into, and assume the pcb is in there...

Thanks, Some of the codes on the sticker............. HNMF 2805A L-80 type PF28 Hope this helps?

Hi Guys, My fridge/freezerr as above has just stopped working completely! Its about 2 years old i think. The light went out and I thought it was just the bulb, however, its not working at all. Its like the whole unit is not getting any power at all, have done the obvious and changed...

Ok guys, anyone fitted one of these before? Supplied by Bathzone, instructions are worse than useless. Trying to work out how to connect the inlet valve to pipework. Its a really odd fitting that they supply, which has a chrome nut, rubber washer, metal rubber and what looks like a small...

Customer service at Bristan are an odd breed. Phoned them a few months ago about a replacement cartridge and the person point blank refused to send one out FOC as we are in a hard water area, gave customer price for new one which they said ok to a few days later. Called to order it, spoke to...