Search results

Hi just built new standard size larder housing unit and want to install 2 appliances. I have a single bosh series 6 combination oven and a series 6 single oven. I have put shelf in at appropriate height for 2 ovens , but I can't find any info on fitting them . Does one just sit ontop of...

Thanks johnd. The joist in corner is further down from end of wall so cant get to it . So will use the drill driver twist bits to take it. The cabinet will also hang on the other wall so should be secure

Thanks guys im looking at some on ebay . They don't say thickness though. Im going to extend it to the joist before the cabinet. ( will be covered by tall housing). But at end near corner their is no stud. So will use a redi driver , I think the 3 joist before it should hold it up. Its a run...

The easiest way would be the rail. But can only see it in small lengths from amazon. As long as its ok with going onto overhanging the end studs. The studs are wood. Any ware else sell it

Got the emails working now. Thanks bud. just wanted to check as it will come from hood. Across wall to spur but buried under pb so its not saw. I've another thread up about hanging cabinets .

I thought no one had replied as diynot is not sending email as it used to. Need to look and see why not

The socket its coming from is a fcu protected by 13a fuse. It goes to a single and double socket. (Total 6 amp). The hood would come from this to a 3a sfcu its the cable from the hood how do I get the flex across to the fcu without it being out zone

Hi guys and gals. Im hanging some b&q cabinets in kitchen onto a stud partition plasterboard wall. The old ones were installed with redi drivers . The new ones wont be no a stud. (recipe for disaster)I was thinking of one of these 3 ways . 1) use grip it plasterboard fittings. But think they...

Ok guys, not got cooker hood yet as finding it hard to get a 80cm one of decient quality. Im putting units up in kitchen so thinking of how to get power to hood. On top of unit to be there is a socket , could a spur be run from that, csble run accross units to a switched fcu, cable from hood...

I've taken down kitchen units and ive renewed a section of plaster 80cm x 90 cm board that was tiled. Ive put new piece up and used sticky fibretape and gyproc easifill to fill the gap in plastetboard. This bit is going to be seen and I can see the tape, am I better using joining compound or...

The socketis out the way and concealed. I was thinking if the lights thro time die and need replace . Would led rope light work ?, around 3 meters. Can't find details on what amperage it would use .

Its for kitchen cabinet lights. Can't run from switch as the switch doesn't have a earth or neutral, and they can't be picked up from another circuit. That's why it comes from fused 5a fcu

Its a double switch

Thanks for replying. It should have said spurred from. The socket will be at other side of room that's going to be powered from switch. Cable getting run under floor, it will he within the regulations for the run.

Picture of proposed wiring. As you can see the earth and neutral from both cables are joined together in box. The switch is to switch the live. So cable from fcu to switch com (only live connected, ). And cable from l1 only live connected. Then all 3 wires connected to socket. Please...

Thanks for answer . I was going to just switch the live through the switch and take the neutral and earth from the fcu that will be powering .the switch Join the neutral and earth to the cable leaving box So when it gets to the socket l, n, and e will be connected to socket.

Quick version. Connect 2 gang way switch to existing one gang switch. Contains 3 wires red.blue and yellow (see pic in previous post). I assume Red is hot, blue switch and yellow for two way switching. ( got two switches in room to control one light). I want to run a socket from the other...

Ok I could have worded it better or took out some clutter (read it through before posting) .

Umn b.a.s . Insulting behaviour. Where is evidence of that ?, lazy ?. How is that . I ask for help. Not to get degrade

Yes red yellow and blue. And taking the neutral and earth from the fcu. Heres a pic of wires . And one of double switch .