Search results for query: b-a-s

any one know where i can get a pair of round things for the top of my fly press. i can not call them b***s as the mods delete my post

Hello all :lol: Though i do not contribute much on here, I am an avid tuner inner so i am sorry to all for butting in on the forum :? B-A-S, greetings to you! I see you are very active on here..... I wish to send you something in the post and they don't do private messaging on here and...

Hi B-A-S, You said 'Equipotential bonding doesn't have to go back to the CU.' (17/12/04) Can you expand on this a bit? I thought that this was the whole point about (Mains) Equipotential Bonding? (as opposed to Supp Bonding) ...and why shouldn't it be 'under the floor'? Is there a Reg...

I am working on a 3.5hp B&S engine with a 'Choke O Matic' carb and there is a problem with the adjustment jet housing. As in the picture below, the housing is plastic with a plastic inner 'sleeve' in which the metal screw sits. This inner sleeve has fallen out and I can see no way that it is...

Only £15 a box. Bargain! At least that's what I thought until I opened the box and found they were smaller tubes than normal. Sneaky B&Q so'n'so s

WHAT DO YOU USE FOR SOAKAWAY,S is it. A. LIMECHIPPING OR B. WILL TELL YOU LATER.

I am re-doing my basement and want to level the concrete floor. It was poured in the 70's and was painted over. But when it was poured, it wasn't levelled properly so the floor is very unlevel. What is the easiest and hopefully a cheap way of fixing this? _____________________ Moderator...

Whats happened to BAS, he used to post all the time, but now it's now and then, unless it's a big debate regarding ( racialism, the death pen, ) Come on bas wake up, :lol:, SHOW US YOUR METAL, :wink:

Hi guys, As advised I have wired my Accenta G4 alarm panel that has the following terminals; Strobe + (not used) Strobe - T (SCB) A (SCB) D (Bell) + B (Bell) - To the AG6 siren that has the following terminals; TR - S - V + V - ST - I wired it as advised as follows: Strobe - to ST - T...

I was wondering if stainless steel self tapping screws were any good for Fixing to standard brick?or a alternative screw but it must not rust or decay Over time,that's why I thought of s/steel.[/b]

Calling all older and wiser sparks. Sorry I know this has probably been asked before, but did a search and found nothing. Could someone please tell this fledgling the differences between the old obsolete breakers, and the shiny, new B,C,D's. Am I right in believing that 1-4's trip nearer to...

Can anyone advise me please? Ten years ago we bought a single drainer two basin kitchen sink from B&Q, Naturally times have changed, but we now need two new basin plugs, B&Q do not stock the size that we require, and to tell the truth were not very helpful, after all it is 10 years...

Is it possible to combine a Y plan 3 port valve and an S plan two port valve onto the same boiler system? This enquiry is made to see if it is possible to achieve 1 x HW zone and 2 x Heating zones within the same system, but without the ineherent bypass problems of achieving pump overrun in...

(De) Stroopwafels

Do I need 3/4 core cable for wiring a conventional S Plan heating system? Please advise. 3 core cable for room stat 4 core cable for programmer 4 core flex for valves 3 core flex for tank stat 3 core flex for boiler/pump Can it all be done in 0.75mm cable or do I need 1.00mm? Thanks

Special Direct System.

That what I thought, also known as Slotted Drive System but looking into it further I've found this, Schnell Drilling System. The most significant recent development was the invention of the Schnell Drilling System (SDS). SDS drills use special bits with slots cut into their shanks, which...

Though it was Small Diameter Spline...... Oh, well

Project Garage/shed - 4inch cavity walls, with ties. Friend works - foundations dug, 1st blocks laid with ties etc, subbase compacted, base poured(4 inches) to groundfloor height. I get to work...DPM overlapped by DPC - above ground blockwork started - PROBLEM.... now at window height...