Search results

It exits vertically through the roof, I don't think installing the fan above the roof would be desirable.

It was about 280m3/s before it broke so plenty of air flow.

I don't know if it's rain coming in or condensation, either way it's not a lot, but enough to for into the fan. Rain will always be able to enter in small amounts if the wind blows hard enough in the right direction. The fan is already as close to the exit as it can be, and all of the flexi hose...

I have an existing bathroom ventilation system where the vent goes through the bathroom ceiling into the loft space, then into flexible insulated ducting, 100mm inline fan, more flex duct, then into a hard plastic pipe that goes vertically through the roof. I've included an image below that...

I've just replaced an old window with a new upvc window. The profile of the window doesn't allow the straps to be fully rotated to 90 degrees as the profile channel it narrower than the strap fingers that stick out. Is this ok to leave it like this, or do I need to find some other straps that...

I had wondered about doing it this way. What is the reason for doubling up the strongboys, is it due to the weight of the 2 skins being too much for 1 strongboy or some other reason?

Ah, I always thought they were metal. Although with the price of timber these days it would probably be cheaper to use metal.

I’ve not found a single hire place near me that hires needles. The only thing I’ve found is something called Prop Pals but can only find the 1200mm version not the 1800mm ones that I would need.

I need to install an insulated catnic into a cavity wall 100mm blocks each side with a 60mm cavity. The opening will be 1800mm plus 150mm bearing each end. I've not been able to find anything that I can hire to support both walls as well as spanning over a kitchen worktop on the inside. Can...

Wall was freshly plastered but was not a great job and was rather uneven, although this could not be seen under normal lighting conditions. The wall was painted and it was only when 2 wall lights were installed that it became apparent the wall was not smooth at all. My first attempt to correct...

Can I dot and dab over the metal mesh in the photo? Behind the mesh is half block wall and half timber. If I can't dot and dab over this what would I need to do so I can? Thanks

Thanks everyone, I'll get a roofer to check out the lead and the weathering collar.

That was the only bit that caught my eye, just wasn't sure if it was supposed to look like that or not. There wasn't loads of water running down so I guess it could be a pretty small crack.

100% not a waste water leak, there is nothing above where the water is apart from the straight pipe going out through the ceiling and then through the roof.

Hi, While renovating my toilet room I notices the soil pipe had a small amount of water running down the outside of it, at the time there was heavy rain. The section where I noticed the water is above any connections in to the soil pipe and from that point it goes up into the loft and out...

All done @JobAndKnock, I followed your advice and it worked brilliantly. Thanks

Thanks @foxhole that is what I was originally intending on doing but started second guessing myself and thinking it was not the right way to do it.

Unless I can stand 2m in the air with the door held vertically I would need to hold the router on it's side (rotated 90 degrees) and I'm not sure that's advisable with a router? I've never seen one being used in this orientation before so I assume it's either not easy to handle, or unsafe, or both?

Hi, I need to cut a slot in the bottom of a 35mm thick oak door (it's a 838x1981mm door) to accommodate an anti warp insert. The slot needs to be 10mm wide and 17mm deep. I'm trying to work out the best way to do this but not having mush luck. I've looked at slot cutting router bits but most...

Just been doing a bit of searching around, has anyone used one of these damp proof membrane systems that can be dot and dabbed over? I assume if they can be used in basements with damp walls then it would stop any issues on a dry wall with no problems? Would this also prevent any cold spots and...