Search results

What would the recommendation be for mounting the below 6U 500 deep cabinet to a stud wall?! Each side has 2 holes at the top but only the outer 2 are 16 inch centres which i believe should hit the studs in the wall. What fixings are best to use, and should I mount ply first and drill...

In order to fit a fuse spur into the loft for Alarm Panel, can i cut this wire, add a round junction box, re-connect the light supply and run a second cable to fuse spur for intruder panel in the loft? thanks.

I have fitted a mainly wired Galaxy Flex System but with an in-panel RF Portal and using peripherals DT8M Pir, D08M Contact and DF8M Smokes. Some devices are on the edge of signal 02/03 and occasionally report RF Loss. I have added an additional C079-2 RF Portal, but only the DT8M Pir and D08M...

I've moved into a property and had trouble getting tv signal from sockets. I've been in the loft and there was a fuse socket and aerial booster attached to one of the trusses. The booster had no led light on so assumed dead and bought another. Checking power before isolating the circuit I'm not...

Hi i bought a cqr sounder which i mistakenly bought the sounder version only instead of speaker/sounder so that i could hear the entry exit tones outside the door when setting. . however that worked fine on intruder activation and sounded. i now have the speaker/sounder version however the...

I had a g2-12 panel at old house with LCE module which worked great with the VKP and push notifications on email/text. I've moved house and now got a flex+ with E080 ethernet card. Remote access works perfect with the GX App but struggling to get the ARC push settings to work. i;m sure i've...

I've setup a few DT8M Wireless PIRs as a quick temp fix before installing some hard wired detectors. Inserted the batteries, all configured as a zone, signal strengh good, walk test working fine, set the system, moved a bit , lit up and set off intruder alarm. However, i left the system idle...

Hi This is going to be very simple for someone to resolve, however i've fitted a direct mount RF module inside my Flex Control Panel. However i cannot exit engineering mode due to RF Tamper I cannot find anywhere in the manual or leaflet how to disable the tamper for the module, seeing as it...

Will a pyronix deltadell WE (wireless version) work with a honeywell galaxy RF portal c079-2 ? the specs say it uses the same frequency. i've hardwired a deltabell to panel before, but with cabling constraints would the wireless version work with the honeywell portal?

I have connected the ALARM out on a Hikvision NVR to a Galaxy Panel Zone using 2 core cable and programmed the zone as 'INTRUDER' I've set line crossing and done a manual test and the alarm is activated however the log (when clear the alarm) shows as a TAMPER Not INTRUDER. I've fitted a 1K...

I self installed a G2-12 system about 10 years ago when moved into house, its been absolutely flawless and no issues with both wired and wireless devices, I'm moving home which again property doesnt have an alarm system so will be looking to install. Currently, I have the G2 with LCE ethernet...

Hi, Just wondered if anyone can assist. For a while now on my Galaxy G2-12 I keep getting alerts approx every 24 hours (which i assume is a self test interval) of: +BAT MIS -BAT MIS -BATTERY +BATTERY I've changed the main backup battery and all batteries in all Wireless devices - PIR, Door...

Hi Everyone, I've previously setup an alarm system with honeywell 8ir103 PIRs with the resisters etc. I'm installing another G2 system and the PIRs are end of life so now using IS312 PIRs. Can someone just clarify which terminals on the PIR i use for each of the 2 data cables, and I presume i'll...

I want to install a 12v dc smart doorbell and run the cabling under floorboards along the joist cable clipped, along with all the twin and earth etc cables. However, am i correct that I cannot run the standard bell wire alongside/near the main 240v twin and earth lighting/socket cables? I might...

I have a galaxy panel which currently has a keypad linked straight to the panel in the loft using all on board zones and an RF portal next to the keypad daisy chained off the keypad. My question is how many data lines can be run off the main pcb from the A B data line if I wanted to add another...

Hi. I purchased 2 x BG Doorbell Transformers both of which I am unable to get any DC output out of any of the terminals. I took them back for another and the same issue. I can't believe that I have 3 faulty transformers but can't see I'm doing anything daft. I can check with multimeter and get...

Hi, I've currently got installed a G2 panel with ethernet self-mon module (all self installed) which has been fault free for 6 years. I'll be installing an alarm system at another property, and wondered if I should still go for the G2 panels, or whether to opt for the flex panel. Is the wiring...

I've currently got a wired galaxy g2 system which has been great over the last 6 years with no false alarms or issues, and only just changed the backup battery this year. On another property i'm looking to install a Galaxy Flex system but thinking of going fully wireless on all PIR's etc to ease...

If i wanted to change my Alarm Panel (self installed) from a G2-12 to G2-48 panel, whats the easiest way to move the bell box connections with making the least amount of noise? I'm assuming that as soon as i remove the current cable connections from the board, the sounder is going to sound until...

I have a honeywell G2 system with majority of sensors wired, but i have 1 wireless PIR DT8M. For some random reason i walked into the room with the wireless PIR sensor and noticed on movement that the red LED was no longer lighting up. I went into zone walk test and set active, however one...