Search results

What i am after is a fitting for this shut of valve here in this link. https://www.caravanparts.express/conversion-kit-for-the-morco-eup11rs-3496-p.asp?gclid=CjwKCAjwjJmIBhA4EiwAQdCbxj_GKWPRI4kXm0E5ASscLWR61VEMtPOb7pL9n5oXLdooDRuW3EcYxRoC3XoQAvD_BwE

Is that a done thing though as in safe, Hamiltons do all the bits here https://www.gasproducts.co.uk/10mm-compression-x-1-2-148-bsp-female.html for the fitting and the olive https://www.gasproducts.co.uk/3-8-inch-imperial-copper-olive.html

#\\\\\#### I measured the pipe and its 9.53mm so 3/8. near .5mm small than the 10mm i have. Measured up th original pipe OD 9.52mm and new ( 10mm ) 9.99mm. 3/8 is 9.53mm. so the original must be imperial size.

Am i correct in thinking i need a female 1/2 bsp to 1/8 bsp male ????

Ok this has my head banging, although tired so hard to think straight at the minute. I have 15mm copper pipe it need to connect to 3/8 copper pipe. Can anyone link me to a compression fitting for a female end for 15mm pipe to male end for 3/8 pipe. This BSP and metric with imp has got me head...

Hi, thanks for the reply, yes it is a party wall. So you are saying that the three walls/footing the walls go down to will not take the extra weight. Infact the tank will be sat on all four walls footings, the wall under the kitchen in th epics where the beams are is not the lower party wall but...

Thought i would go on an adventure to the center of our house. Wish I never...I think. These are picks of uder the floor

Hi tony, yes it is a suspended concrete floor in a semi house. the concrete is a 6 inch thick, not a clue on the reinforcement though, i do remeber there was also two RSJ under the floor, which i thought strange, but hen i am not a floor expert. I was thinking the best support on the floor for...

I was wondering the thoughts on if a suspended concrete floor in a 50 year old Ex council house would take the weight of a water tank sat as in the pathetic pic i have drawn below, it will weigh around 2500kg, so around 1 1/2 pallet of bricks, sat right up to the three walls. the footing go down...

which would that be

I am building a fish tank that is an L shape and weighs around 6000kg base size is each leg 10x4.5 foot from back corner. what thickness slab would i need to go for, the overhang shall i call it ( beyond the tank base ) will be 200mm ? I am thinking 6inch with rebar aswell. any help...

Both discs will do the job, the thinner will just be less on producing sparks and cut cooler but wear quicker, and if not to steady with the hand can shatter easier, so IMO use the thicker ones, aslong as you can get all around the pipe you will be fine, dont force the disc in, let the disc do...

never heard of that way to laminate, i could be wrong though, if you add enough resin to the base, then matt then roll in more resin that should do, not to let dry then add more resin, unless your late and the first lot sets then you need to add more matt. Dont sound right but if it works and...

It would of been best to as i normally do when i do similar jobs, but never done a roof yet. there is still a joint in either TnG or butt joint. how many laminations did he do? and what thickness?

Hi that sounds ok but i will be using this way as they show here http://www.glasplies.co.uk/Roofing-Information-s/1873.htm i think it would depend on what topcoat he used. aslong as he gave a coat of resin onto the OSB before he laid the fibreglass, if not it will not bind to the OSB...

sorry about that, i am useless at saying what i mean when typing, try to make it short as otherwise it will be a very long winded message, folk dont often like to read to much. So if i keep the external dividing door then i can build it with just PP and no BR will need to be involved, but...

The £1100 to build it is for the materials to extend the con`y and fit a flat roof, unlikley to building regs though as i have been reading and they are in a word `costly` to be done there way. I am just now starting tp look into what the regs are and what needs to be done and materials used...

Hi all, after years of wanting a decent size fish tank and running out of paces in the house due the size and weight of them i have decided to convert the con`y i built about 3 years ago into an extension and extend the cony/extension in to the workshop i built onto the back of the house, i am...

We have a 10sqm con`y i built about 3 years ago and now i want to convert it into a extension and extend the area to another 12sqm, fo this i will be needing planning permission as oit will be extended 5sqm towards a highway, also reason i had to get PP for the con`y in the first place. Now i...

It does my head in at times asking questions on here, i didnt say i cant or dont know how to do it. Thanks Norcon, i will take a look :wink: