Search results

or the type of cable I was looking for.... Thank you for suggestions.

OK, had sanity check, and was not going mad. so the cable that I put a terminal block on had to be there just not where I thought.. Expanded the removal of loft insulation, and found old hole, that had been filled, very much closer to the new light than expected (she still thinks it was in...

Sorry maybe should have been clearer: Single storey extension, so no between floors. The lights are mains so no transformers, have looked at hoods. The previous light worked from both switches I have removed the insulation from the area so it is now clear nearly to the new lights. I...

Even as a sanity check I have asked visitors where they thought the old light was... (people who have been to the house before!) so the question is, as the cable does not seem to be there and no sign of cables in the loft space from the switches, how would you wire in these lights...

And the picture should be here...

disappearing hole good, disappearing cable not good!

Picture of Dinning room

Many moons ago it was decreed the artex ceiling in the dining room would go, and so would the single CENTRAL (will come back to this) light, replaced with 4 downlighters. From inside the dining room, central light removed and terminal block connected to cable. Plasterer did great job...

So it works OK on the pre wash.. but when on proper wash nearly finishes but then starts a cycle of, you can hear what sounds like water going in, a pulse sound (drain?) then beeps twice makes a noise beeps once, waits 10- 15 secs and does it again. if I open the door it is all clean and...

The tube is clear, blowing and sucking.. You can here the "switch" mechanism but the knob on the outside does not turn. no matter where the switch is on the dial (wash program) it does the slow spin thing, here indoors is pushing for new one.. Spin another day looking for a replacement...

Changed the brushes... still stuck on very slow spin, spins very slowly 1 revolution... then stops for about a minute, then slow spin again.. What do I blow down? something is stopping it going to the next cycle, but I do not know what that is she is now 1 week with out Washing mc...

my Hotpoint Aquarius 1200 WM64, worked fine, but is now stuck on an intermittent slow spin, it does not speed up at, and when I turn off and change the programme, it stills continues in the slow spin mode. I have taken off the drain hoses and cleaned etc. any hints or ideas it must be the...

Sounds good to me do you have mobile no or works no? one boiler engineer has been suggested, been contacted but no response yet, so will give 24 hrs to contact..

Fan seems fine, Ok got it Air pressure switch... all seems OK time to get profesional ... any service engineers that can be recommended in the Hamilton Area?

With the Hot water on the boiler switches on for about three seconds then off for about four seconds, and repeats approx cycle, the initial on phase may be a little longer, but not much! Hope this helps the Diagnoses

Problem as above when the hot tap is on the boiler fires up but quickly shuts off, so the water is slightly warmed then flows cold the boiler continually cycles on and off, with out getting to a constant high temperature, this happens on the hot water and central heating.... The diagphram has...

Hi Ridgetop, if you can point me in the right direction it would help. If they are that scarce, maybe if I buy new roof slates etc, I can sell the Delta's to recoup some of the cost of the new ones, There are about 650 Delta's on the roof. I am not working at the moment so tight budget...

I can build you a web site, a simple web site, with the information the customer needs, with a bit of backgound and some of your work should only take a few pages to start with. an example of my work http://www.candgscotland.co.uk/ (this is no longer updated as they failed to pay the bill...

After much suffering of damp and leakage, it has been diagnosed my tiles have insufficient overlap2-3 inches instead of 4-6 inches, so I need to relay or replace two questions 1) can you identify the type of tile 2) these tiles are about 20-30 years old, how long do they last, I will need...