Search results

Hello All, here’s a tricky question to ponder. I’ve fitted lots of laminate before, but this project in my dads house is tricky. Photos attached. I have purchased two colours from the same range. They are edge compatible but different widths and I was hoping to join colour 1 to colour 2 in the...

Thanks for your replies. The distance to the wall from the center is 210mm. If there is space for a short pan connector, then I guess I can use an offset connector instead. That’s great. I was concerned the ceramic of the pan outlet would be flush with the base, thus leaving no space for a...

Hello All, I’m looking at fitting an Ideal Standard T3280 bottom exit pan to my soil pipe, which is clay, with a new adapter fitted. I might need to offset it a little from the wall. 5-10mm, which would add additional hardware vertically in the form of an adapter. My question is, how much...

Here we are... The conservatory brick line is sitting on a lintel over the original drain brick line, then the next lintel supports the cover frame. New footings were sunk all the way round to take the lintels and offset bricks.

I will chat to my builder about it. He is coming at the end of the week to start the footings. He won't order the conservatory until he has the size. The digging will be a look see, to see what options are available. Again, thanks to all for your comments and wizdom

The 6 o'clock is an addition from my extension. It goes about a foot, then goes off at 7:45 ish up and towards the house.

The lintel would in theory be below ground, then two bricks up on top of that, with DPC and insulation and concrete top. I would be surprised if any smells could get through, however smells and water are strange beasts that do defy logic. :(

Many thanks Hugh, yes 10cm as in the picture. The new position will still allow fully vertical access to the drain for rodding. I'm just mindful that I don't want to break any regulations having the corner of my conservatory on a lintel over 10cm of the chamber.

Basically I want to move the cover 10cm to the right

Hello all, long time, no post. I could not have done without all the amazing help on here when I was doing my extension. I'm back with a new question. I'm having a small conservatory 3m x 1.6m. No dwarf wall. One corner of it will terminate right at my drain cover. The whole cover assembly has...

Hello All, I thought I would start a new thread about this boiler. My original Vokera Excel lasted at least 15 years but finally needed replacing. My Boiler man had let me down during some work he was doing which forced me to find a new engineer. I got a number of quotes, but each company...

I'm just a consumer, and i'm going for the logic+. Based on my heating engineers personal experience of Ideal and from looking at the literature etc. I can't afford a top of the range brand, and my engineer fits preventitive bits like Magnaclean and descaller etc.. I must admit, I am...

I'm just a consumer, and i'm going for the logic+. Based on my heating engineers personal experience of Ideal and from looking at the literature etc. I can't afford a top of the range brand, and my engineer fits preventitive bits like Magnaclean and descaller etc.. I must admit, I am...

Hello All, My friend has asked me to replace a washer in her kitchen tap. I managed to get the knob off the top, but cannot unscrew the cover below. I have tried mole grips with a rubber glove as protection , but it will not move. (I assume it should unscrew) Has anyone got any tips to...

Hello All, Just to update; Mira came and looked at the shower, and told me it had the wrong washer fitted during manufacture. They changed the flow module & now the shower is very quiet. (all done under warranty) :D If it helps anyone else with the same issues, my shower was made in...

If the temperature dial was a clock, then the range that makes the scream would be 4 hours eg, 9 - 12 o-clock. I tried reducing the flow into the house and this moved the problem further round the dial, eg 1 - 4 o-clock. Moving the problem has solved it as the shower temperature we require...

The pressure was 4 bar. I think I will get mira in under the warranty...

Cheers Agile, I will pick one up.

Hello All, I have a 6 month old Mira Sport Shower and it has always screamed when on, although you could stop it by adjusting the heat. Just reciently, it has got worse and seems to scream at the exact temperature that would be just right to shower. Mira have said they will come out to...

Many thanks Softus :D