Search results

Hi wondering if anybody can help we have a Biasi m90f 28s combi which is running fine apart from a problem that has developed. when the water in the heating system reaches its high temp setting (about 65c) it shuts the flame continues circulating as it should. Then after about 20 seconds flames...

whoops i did not see that typo, been having problems with my r's for some time must see somebody about that. thanks for the help looks like on the return in the cellar then. much easier connection, out of sight and easier to check for maintenance

thanks for the reply our boiler is on a wall on its own above the kitchen rad with all the pipes neatly boxed in. i have nowhere to hide an expansion vessel and the kitchen has a solid floor. it is possible to fit in the kitchen but do not think the Doris will be happy with an 8 litre red...

Hello again looking for some advice regarding the siting of an external expansion vessel on my CH system. the present system has been recently extended and the capacity of a couple of the existing rads increased. we have noticed there has now been an increase in boiler pressure when it has been...

would the pre heat cycle use a different element. when it goes through that pre heat cycle it pings when the oven reaches temp. the oven is warm/hot after pre heat. then we turn the dial to the required oven you can hear the fan but the oven goes cold

Hopefully somebody can give me pointer to save Christmas dinner. our Samsung BF3ON3T11 built in oven has developed a fault. When using the oven it will run through the pre heat cycle warming the oven but when that finishes and you switch to either top or bottom oven in fan or conventional mode...

Hi i have a biasi m90 f combi about 5 years old which is running fine in CH. But when you ask for DHW unless you strangle the flow rate through the tap the temp is only tepid. Had a bit of a closer look this morning before the CH had been fired up. Water took a while to get any heat in it...

I will release the pressure at the injector rail before i start to change the filter. What i am worried about is knackering the fittings as they will be main agent only parts and i need the car early monday morning for work. One of the fittings looks like it has a couple of tabs to press which...

My 406 fuel filter located under the car near the offside rear wheel has started to leak. Does anybody know how to remove without damaging the fittings on the fuel line. Thanks

Boiler now working thermistor faulty fixed by engineer. Thanks for all advice given

Thanks again Tony for the quick reply, removed motor its dry the actuator pin did not seem to fire just sort of slides loosely in the motor body. Also pressed the diverter valve pin and started the boiler but still no CH. Now starting to look like an expensive fault :cry:

Tony you are probably right regarding most of the possible faults being beyond me. I have tried to get it in diagnostic mode following the service manual instructions (not sure if i have done it right) but those attempts do not show any code other than boiler operating normally. On the primary...

Hi Need some advice i have a Biasi M90F 28 combi boiler. Arrived home today to find CH not working. The boiler trys to go through the start up procedure for a few seconds then shuts down. The green operation light flashes at its normal speed about once every 3 to 4 seconds and the lock out...

Removed the lifter bars. Isolated the noise about 3 inches past one of the lifter slots at the back of the drum. You could hear the foreign object moving across the heater element but could not see anything. So just gently turned the drum back and forth so the offending object just kept catching...

ok thanks i will check it when i get home from work tomorrow and will post what i find. Once again many thanks for your help and patience much obliged

The black pipe that i can see is underneath the drum at the front jubilee clipped in place. The heater is at the back. If i take that pipe off i still dont think i be able to see or reach where the noise is coming from

Hi again just had a quick look underneath. At the front of the drum is a blacl pipe that goes to the pump i think. Underneath the drum at the back is the motor. I can see the wires connected to the heater. If i take the back off is it possible to remove the heater to get access that way

Thanks again rocks1, just removed all 3 lifters and slowly turned drum. Nothing in the bottom of the drum. Scraping noise seems to be from the rear of the drum when turned by hand. The knock seems to be something catching the heating element, guess i need to call them out and hope its a warranty...

Thanks rocks1. I make a decent cup of coffee but at 6 foot, 15 stone and with a couple of days stubble on the chin the fluttering of eyelids is unlikely to get a discount and possilbly result in one disturbed engineer having nightmares for weeks. I have looked in the inner drum and can see...

Need help or information urgently please. Bought this machine new in May so it is still under warranty. It has started making a loud knocking/scraping noise on the spin cycle. The noise appears to be caused by something between the inner and outer drum. A daft question but would this be covered...