Search results

No not really cos the pipes would end up in the middle of the ceiling as where the shower enclosure is fitted the ceiling slopes. Also I need to run the pipes behind the shower in order to plumb it in.

It's very cold... in fact then I saw it under the floor boards it was sweating.... I can try & follow it from the bathroom downstairs but can't be sure it the correct pipe... Maybe I should just tee off the bathroom downstairs then run the pipe up. I've got to rip out a lot of tiles.... I've...

Thanks Serco Services... can I ask... I've got a pipe running under the floor which appears to come from the bathroom downstairs.. which I'm guessing runs to the tank in the loft..... (i.e. a mains pipe) is there anyway I can check if this is the case?

I've done what you suggested Tamz & yes your right the bathroom is plumbed into the tank in the loft. When I turn of the kitchen stop cock the bathroom still flows. Let me get this right so I don't screw it up again.... the tank in the loft I should be tee'ing off is the big one & not the...

Hi All, I've got a Triton Jade II electric shower just been installed. The low pressure light is constantly on as soon as power is feed to the shower & the water runs cold. The shower is an old one which was installed in my last house & worked fine there. Its been sitting around for about...

Hi, I've got a Triton Jade II electric shower just been installed. The low pressure light is constantly on & water cold. The shower is an old one which was installed in my last house & worked fine there. Its been sitting around for about 2 years & now installed having this problem. Can...

Hi Guys, Just need some advice. I'm fitting a new sink to my small bathroom. My question is can I just run the sink waste pipe to the stack & drill & hole big enough to accommodate the pipe. Then just seal it with silicon or should cutting the waste stack & fitting a particular waste...

Hi, I'm laying floor tiles in my kitchen. :lol: The problem is the kitchen door (UVPC) sit too low and there is only about 2mm gap between the door and the floor. The door doesn't seem like it can be taken any higher. :cry: Any super ideas what I can do to get these tiles layed...

Hi, Thanks guys for all the help & advice. Hopefully I can get the dam thing out without damaging this coller. :roll: Any little trade tips how to do this with minimum damage to the cooler? :wink: Cheers, Andy

Hi, I've just moved into an old property and one the toilet waste pipes seem to be going into the floor into some Red Concrete circle, not the conventional waste stack. :? My problem is that the toilet is one piece including the waste pipe which has been cemented to the floor and then...

Hi Chris, It's a duel fuel cooker. The hobs are gas and the ovens are fan assisted. The socket for the cooker is a dedicated switch for the cooker but it also has a spare socket for other appliances. I was told the heat from the cooker could cause a fire so the socket needed to be moved...

Hi, Can anyone help!!!! :roll: I'm fitting a part electric cooker but have been told I need to move the electric socket as its above the cooker which is dangeous. :cry: Can I just but a junction box where the socket is now and then run the wiring across the wall to the desired...

Cheers....... Guys for all the help, much appreciated..... :lol:

Hi Guys, Just need some advice.... :? I've got large tiles (appox 4/5 times the normal size tiles) marbel they are fairly heavy & thick..... My question is: I have to tiles them onto plasterboard on some walls.... will they stay up or do I need so sort of special glue? Any Help &...

Cheers Guys for all the help much apperciated...... :wink: will give that a go over the weekend...... if that doesn't work I think it would be a good idea to get in a sparky or just leave it alone..... Andy :)

Cheers guys will try that over the weekend when I can work during the day so I can turn the electric off..... It would prob be a good idea or I'll get fried..... :shock: Just one other question.... the new switch has one comm port for each button and 2 ports for each button on the other end...

Hi, Just to confirm: In one of the lights there seems to be two red wire going into different ports, a black wire going into another and an earth wire also. In the other light there seems to be wire "madness" :shock: there is 3 red wires going into a comm port and another red wire...

Hi........ :D I'm trying to change my living room light switch for a 2 GANG swtich. Some professional advice would be much appericated..... :wink: The 1 GANG switch I currently have turns "two" light on with the one switch. I want to put in a 2 GANG switch so both light work...

Hi ColJack, Yes, sorry what I mean is I want to change to a 2 GANG from a 1 GANG.... Cheers

Hi, I have a light switch in my living room when truned on it turns on both lights. I want to put a 2 way switch so each light can work independantly... There seems to be 2 red wires going into one opening and one black wire which goes into the other. Anyway idea how I can change...