texecom

Good morning, I've got a Texecom Premier Elite 88 with 4 Capture D20 PIRs, each wired as EOL on their own zone. They all have selectable resistors and are set to the Texecom setting (2k2/4k7). 3 of them work fine, but one of them goes to Tamper (>100K) when triggered (by both PIR and Microwave)...

Hi, I've recently self installed a Premier Elite 64-W. I'm now looking at integrating it with Home Assistant (I've got no interest in using the Texecom mobile app, just HA) From what I've read I think I can use SmartCom or ComIP for HA, and the SmartCom seems a lot cheaper. But what else am I...

Hi folks, Hopefully someone can help, for the life of me cant work this out. I've recently moved into new prpoerty which has a Texecom Elite 24 system installed. All is working fine, and the remote access app is working great. On the keypad it has the date and time showing, but when a person...

Hi - I've had a texecom alarm installed for 7 years and I recently noticed I can no longer generate an app code on the keypad, from "Enable Texecom Connect App" I receive the error code 'No Carrier'. I've checked everything I can think of, but without any success, anything else I should check...

Hello, I have a Texecom alarm system installed with the smart com, generally it’s all done by an installer but I recently changed my router and didn’t fancy paying someone to update wifi details and did it myself, however since then the cloud led is just flashing and will not connect. I left it...

Hi all, A while back I tinkered around with my professionally fitted Texecom Premier Elite 24 using Wintex to change the configuration so when we part arm the alarm, the living room is omitted to avoid my cat setting of the alarm at night. Everything was a success and was working fine. We're...

hi I haven't been able to find much info on how to connect the USB-COM lead( jac-0001) to my premier elite panel to program it. what is the exact procedure that I need to take to plug the lead in? I think the steps that I need to follow are... put engineer hold on siren, remove fuse from...

hi, i reset the wifi on my texecom smartcom (holding the button down for 5 seconds etc). Now when i try to connect to the smartcom to connect it to my router, it asks for a password straightaway. It usually let me connect without password and then i put in the passphrase inside the smartcom in...

I’m planning to upgrade my Texecom Veritas R8 system to a Texecom Premier Elite 64W, retaining the existing Texecom bellbox. Obviously the bellbox will be staying in situ, with just the control panel/keypads being changed for the new one. My concern is whether the bellbox will go off during...

Hi, I have a Premier Elite 24 that many moons ago, I bought a comport+ (JAL-0001) and comWIFI (CEK-002) module for. It never worked properly and I since got Smartcom. However - I now want to connect the alarm up to Home Assistant and believe I need another 'connection' (is that right?, as...

Looking for some assistance with Texecom Custom Outputs for a specific client request... Client has a Texecom 64-W panel with a Hardwired 8XP Expander into their Garage. On the exterior of the Garage, there is a Master Blaster which is wired into Output 1 of the Expander, They currently have...

Hi all, first post here! I've got an texecom premier elite 24 existing setup with a smartcom on com ports 1 and 2. I also have a ComPort+ model A5147-02-01 connected to the Digi Modem on the main board (currently used just as a backup if connecting over usb). I want to add homebridge capability...

I have recently had installed a texecom alarm with the app which was great but we had to do a master reset when we installed a wireless keypad to get that to pair up and we lost all of the app etc. We have got it all working again apart from the app and and it says the following You have...

Hey all, Thanks for the useful threads I've read so far here. My Electrician installed a Premier 24 and set it up with two areas (B upstairs/A downstairs), but part arms never worked correctly. He also didn't know about Wintex, so I have now registered and set that up myself via the...

Hi everyone, I'm in a bit of a bind with my alarm! I had a texecom premier alarm fitted a few years ago to replace an ancient alarm system in my house. Whilst the engineer I had to fit it is a good guy, he's EXTREMELY difficult to get hold of. Often working long periods away and not responding...

After opening up my Elite 24 for the first time over the weekend, it was suggested that it be useful to check whether it's got some sort of communicator for monitoring. I enclose pictures of the main panel but not sure what I'm looking for. Many thanks

I've been in a new place with a Texecom for about 3 months and this morning (why is it always weekends?) the control panel has started alarming with a "call engineer" message and I can't work out how to turn it off. Manual is for "Premier 412/816/832". Code supplied by previous owners not...

Hi, recently installed Premiere Elite 48 with Smartcom 4G, alarm works as expected, cloud is fine along with connect. The Smartcom 4G is connected with ethernet/LAN cable which works OK, but, for some reason the unit does not seem to think 4G is operational (no light), or even present. When...

Hello everyone. This is my first post so in case I did something wrong - please forgive me :) According to what is on the screenshot - I excluded the sensor in Part 2 arming mode, and despite that it still activated. Can you tell me what the potential reason could be? I warned you and...

Hi Can anyone help we have a texecom veritas alarm system, is there a way to set the full alarm but reduce the noise it makes when it’s setting as ours is really loud. If not can the part set be changed so the silent alarm doesn’t set the alarm off straight away when front door opened?