underfloor heating

Looking for advice on UFH as well as general heating system. We have made the choice to get water underfloor heating in the middle of our refurb works for the kitchen. Rather than placing PVC pipes in plastic castellated floor panels, we will have them routed between joists and on top of...

Hello, The issue is similar to this thread? Don't know what to do (or if it's the same) as there's no follow up....sorry. :confused: https://www.diynot.com/diy/threads/underfloor-heating.301227/#post-2199695 The thermostat is a TH132-F. Connected to a conservatory floor of approx. 10m²...

Hi, We have a large village hall that we've installed UF heating in - wet system, covered in 75mm concrete screed. We don't have the sufficient drying time so looking to put down a liquid DPM ahead of an engineered timber floor (all flooring, underlay etc is UF heating- compatible). We'd been...

We have had Cozytoes heating matt laid and tiling done. They have come to install the Touchscreen Timerstat and they have realised they forgot the Probe/sensor that lays under the tiles amongst the matt. I know, cowboys, plonkers, not paying for it etc etc. However is it possible to fix this...

Good Morning, I am in the early stages of planning the central heating system to install in a stone cottage. The property is currently served by a truburn solid fuel range with a back boiler capiable of 90 000 BTU (26kw)in 24h feeding a 117l tank. Aside from this there is no other heating...

Hi All I was hoping to get some advice regarding my underfloor heating. Setup is as follows: 6 circuits connected using 1 6 port manifold Grundfos UPS 25-60 130 pump Polypipe mixing valve All controlled as a single zone, no actuators, wire thermostat Worcester boiler (with a pump inside it)...

Hello all. Just in case one of you knowledgable people understands the intricacies of flow and return planning I'd like to ask for your advice. I've just ripped out most of the old ground floors in my house and laid underfloor heating. I've laid a new flow and return from the existing...

I have a wet underfloor heating system installed between joists in a 1930's house. The heating system itself works. The issue is with the subfloor.... The builder installed insulation between the joists, then clipped the pipes to the insulation as seems to be the standard approach. He then...

Advice please! I have a 5m x 4m extension underway. Got my slab down, with the insulation boards under whacked down type 1 below the slab. My plans say to put 75mm screed down, BUT no allowance has been made for dry underfloor heating - and the bifold company are due to visit for measurements...

New to this, so please excuse if this is a obvious question. I have a ceramic shower base that I need to put into a very tight space that is closed on three sides. The base is to replace a base that was put over a cemented in heated floor. I have been told putting a shower over a heated floor...

I have tried a number of local plumbers but unfortunately, have had no success. I have a vented heating system and am running a glow worm 30 HXI boiler, approx 2 years old. It is a three zone system - one zone is the underfloor heating consisting of 5 loops, another zone is the rads consisting...

Hey guys, I'm going to be installing underfloor heating with 10cm insulation, topped off with a 5cm screed. The area is just over 35sqm and will have a kitchen, so there will be electrics, water supply and a drain installed. For the drain to work, it obviously needs to be at a slope. The...

Hi Perhaps someone might be able to assist me pls. I will be putting in underfloor heating in a flat/apartment. The rubble has been cleared from between the joists. Insulation will be put in-between the joists. Then aluminium plates, resting on the joists, but sitting between the joists will...

Hi I have a 12sq m Electric underfloor heating mat rated at 200W per Sq Metre Total of 2400W. A quick check online calculator indicates 10AMPs. The feed to this spur is on 2.5mm electrical cable and is not part of a ring main. Its connected in the fuse box to a 32amp breaker. We also...

Hi, Renovating the kitchen where I have a concrete sub floor with some cracks & high points. What's the best option to lay underfloor heating on-top of this on a budget while trying to keep additional height down to a minimum. I will need to grind down the high points but do I really need to...

Hi - could I source your thoughts on concrete drying times suitable for flooring? We've replaced a ground froor slab (44m2) with a DPM, 6" concrete, 100mm kingspan, and 65mm Anhidrite Screed containing a wet loop underfloor heating system. The Screed pour went in 33 days ago, followed by...