Cistern outlet Dudley male thread 45mm into a modern flexicon4 compression 40mm

Joined
18 Nov 2026
Messages
5
Reaction score
2
Country
United Kingdom
Hello everyone, I am desperate for help please. I am connecting a new toilet pan to the existing cistern, which is Dudley and very old but works fine. The new toilet pan is a bit higher than old one so flush water inlet is like 10mm higher than previous. I am have connected a cone in the water flush inlet in the toilet pan, then a McAlpine flexicon 4 https://www.screwfix.com/p/mcalpine-flexcon4-flexible-connector-white-40mm-x-157-242mm/86386 with a piece of 40mm pipe to the cone. Then I need ot connect the flexicon 40mm compression end onto the cistern. This is where I need help as I have bought many parts that dont work for this connection. The thread of the male output of the cistern is around 43mm, and I have the nut. I tried fitting the same 40mm pipe onto this male outlet so I can then connect to he 40mm compression from the flexicon. But the nut is smaller is for a 38mm pipe so I cant connect the cistern to the flexicon. the height is very small to make a decent fall we have around 50-60 mm gap between the end of the cistern outlet to the flexicon 4. Please can you help me by the parts I need to finalise this connection? I have attached pictures . thanks a ton
 

Attachments

  • WhatsApp Image 2026-11-18 at 18.47.45.jpeg
    WhatsApp Image 2026-11-18 at 18.47.45.jpeg
    180 KB · Views: 19
  • WhatsApp Image 2026-11-18 at 18.48.06.jpeg
    WhatsApp Image 2026-11-18 at 18.48.06.jpeg
    147.5 KB · Views: 20
  • WhatsApp Image 2026-11-18 at 18.48.21.jpeg
    WhatsApp Image 2026-11-18 at 18.48.21.jpeg
    138.3 KB · Views: 19
  • WhatsApp Image 2026-11-18 at 18.46.37.jpeg
    WhatsApp Image 2026-11-18 at 18.46.37.jpeg
    237.5 KB · Views: 20
That’s wrong and rough on many levels. Just trim existing or buy a new flush pipe and trim accordingly
 
Thanks but the flush pipe has the problem that i need 38mm to fit into the cistern outlet nut and I cannot fit it into the cone I fit in the water flush inlet in the toilet pan as when i tried it is very lose, when i fit a 43mm pipe (40mm inside) the cone fits tight, am I doing anything wrong?
 
Thanks but the flush pipe has the problem that i need 38mm to fit into the cistern outlet nut and I cannot fit it into the cone I fit in the water flush inlet in the toilet pan as when i tried it is very lose, when i fit a 43mm pipe (40mm inside) the cone fits tight, am I doing anything wrong?
Toolstation do a rubber flush pipe connector that is a standard 58mm OD and 38mm id for the flush pipe to fit tight.
Sling that connector you have and buy a rubber one using the 38mm pipe you previously had.
 
Countryfan, the 38mm flush pipe fits the cistern but doenst fit the pan as when i insert in the cone it is too lose.Sorry I am not a plumber I try to explain the best I can
 
Countryfan, the 38mm flush pipe fits the cistern but doenst fit the pan as when i insert in the cone it is too lose.Sorry I am not a plumber I try to explain the best I can
That makes sense, thank you. You could try the rubber one as mentioned by Avonmouth.
 

If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.

Select the supplier or trade you require, enter your location to begin your search.


Are you a trade or supplier? You can create your listing free at DIYnot Local

 
Back
Top