Pred looky here...

[streaker99]

Isn't this beautiful...
and cheap , who cares if it's a chinese copy with a wheezy 11bhp.
I would get one just to shop hop into town.

I bet it would get crowds wherever you parked it. £1675otr !!!

 

[pred]

If i saw that whizz pass me i would assume it was WS66 on an Aiermachi thingamejig. bit small for me, i'm now toying with the idea of, if i get shot of my Mille, getting a big BM flat twin, 1969 i was 6'2" 16yrs old 12stone or so, now i'm a bit older and practicaly twice the weight, the problem is getting the knees to bend onto the pegs and maintain the race crouch

 

[LastMagicBean]

I'd Rather take a brisk walk.

 

[pred]

I'd Rather take a brisk walk.

Probably better for your health, but i say BUT boreing

 

[streaker99]

I'm borderline for it tbh. but a treat for any new riders or older small guys fancying a weekend pootler.

Its actually a chinese copy of the bike Honda have made to celebrate 50 yrs racing.

Honda produced a retro racer with 50cc...in 2004.



http://exoticrarebikes.com/honda/45-HONDA-DREAM/64-honda_Dream_50.html

The retro racer had 50cc 13,500 revs and 7bhp.

The copy has 125cc and 11bhp but the same looks.

 

[LastMagicBean]

Trouble is with these particular bikes, They have massive trouble with the pigeon box valves.

You can get round it, by fitting a westermatactic capillary drive system, Backed up with the obvious gravity fed halo banchee injectors.

 

[Nige F]

LMB - I think your magdyno is loosing it`s flux - needs a rewind

 

[conny]

LMB - I think your magdyno is loosing it`s flux - needs a rewind

LMB PM Me I'm an armature winder I can do that for you.
£200 call out and then we'll work out an hourly rate from there.

 

[Whitespirit66]

If i saw that whizz pass me i would assume it was WS66 on an Aiermachi thingamejig.

If you want, I'll knock you up a frame in 22mm copper with my bender. Proper end-feed joints. Just bolt on wheels, engine and seat, and you'll be cruising down the Golden Mile in Blackpool before you know it.

 

[Whitespirit66]

EDIT

 

[pred]

If i saw that whizz pass me i would assume it was WS66 on an Aiermachi thingamejig.

If you want, I'll knock you up a frame in 22mm copper with my bender. Proper end-feed joints. Just bolt on wheels, engine and seat, and you'll be cruising down the Golden Mile in Blackpool before you know it.

Great, though what sort of power plant did you have in mind, personally i think rubber bands are underated.

 

[Whitespirit66]

If i saw that whizz pass me i would assume it was WS66 on an Aiermachi thingamejig.

If you want, I'll knock you up a frame in 22mm copper with my bender. Proper end-feed joints. Just bolt on wheels, engine and seat, and you'll be cruising down the Golden Mile in Blackpool before you know it.

Great, though what sort of power plant did you have in mind, personally i think rubber bands are underated.

Wasn't planning on that sort of torque. May have to use compression joints in that case. Or I may be able to get my hands on a low mileage Melody lump.

 

[AronSearle]

who cares if it's a chinese copy

:raises hand:

 

[pred]

If i saw that whizz pass me i would assume it was WS66 on an Aiermachi thingamejig.

If you want, I'll knock you up a frame in 22mm copper with my bender. Proper end-feed joints. Just bolt on wheels, engine and seat, and you'll be cruising down the Golden Mile in Blackpool before you know it.

Great, though what sort of power plant did you have in mind, personally i think rubber bands are underated.

Wasn't planning on that sort of torque. May have to use compression joints in that case. Or I may be able to get my hands on a low mileage Melody lump.

Forget the 22mm copper tubing, its far to exspensive anyway, i saw the ideal lump a few weeks ago, it's still attached to the vehicle but i know some lads in Southmead, it was a silver Fiat Scudo with a long tube like carry case for pipes on top, for this lump i reckon we can make do with 15mm plastic pipe. wotduthink

 

[Whitespirit66]

Speedfit and pushfit.