Making neat cuts in lathe and plaster ?

Joined
12 Jul 2019
Messages
170
Reaction score
5
Country
United Kingdom
Hi,

I'm trying to cut into a lathe and plaster stud wall (to run some piping inside) then fix plasterboard over the top once done.

Been using a multitool but the vibrations are makjng a hell of a mess (and loosening all the plaster in the lathe)? Is there a better way??

thank you
 
Sponsored Links
Sharper multi tool blade? Take plaster off laths first (several times round the perimeter with sharp Stanley) then try and get a clean cut on the laths? Use a holesaw drill attachment to make several holes? Don’t think there’s much else you can do as it’s always going to get disturbed a bit if it’s that fragile
 
Maybe an angle grinder with a slitting disc?
It would probably make the heck of a mess
 
I've been using new blades on the multitool, I think its the way it vibrates that causes all the mess.

Angle grinder may be better, I've been eyeing up one of those mini circular plunge saws! just reluctant to buy yet another tool <sigh> before knowing its going to work :)
 
Sponsored Links
Clamp the wall with pieces of wood either side of the wall next to where the cut will be made.

Use screws or bolts through the wall to pull the pieces of wood togther while cutting.

If the surfaces are very un-even then use padding between the wood and the surface

The small holes for the screws can be filled in afterwards.

Depending on the "quality" of the wall and the size of the hole it may be necessary to anchor the cut ends of the laths to a lath set at a right angle to the existing cut laths
 
A baton on the wall is always a good idea- or make a plate that has a slot in it.
Do you have a jigsaw?

A small plungesaw is £50.
 
Bosh it all out then fix it. No point faffing as the repairs will take the same amount of time, cost the same amount of money and will save you faffing about.
 
Clamp the wall with pieces of wood either side of the wall next to where the cut will be made.

Use screws or bolts through the wall to pull the pieces of wood togther while cutting.

I think I understand. Seems a lot of work but may be the only option without buying more tools

Do you have a jigsaw?

A small plungesaw is £50.

Have a jigsaw but need to make the cuts along the studs so as not to weaken the lathe and so I can replace with plasterboard once done.

Leaning towards the plungesaw, I may then own every type of saw known to man!
 
They are handy
I used to buy factory repaired tools from a black and decker outlet.
They were checked, repaired if necessary, and sold cheaply with a full guarantee.

But the guy in the shop told me that it was quite common for people to visit b&q on a Friday, buy a drill, put up shelves and return the drill saying it didn't work. Not that I would recommend such a thing.
 
Bosh it all out then fix it. No point faffing as the repairs will take the same amount of time, cost the same amount of money and will save you faffing about.
That is all true but I'd then have to take the whole wall of lathe and plaster out. Its the clean up that scares me. Room is currently a bedroom trying to keep disruption to a minimum
 
That is all true but I'd then have to take the whole wall of lathe and plaster out. Its the clean up that scares me. Room is currently a bedroom trying to keep disruption to a minimum
Using a multitool in a bedroom is hardly dust free.o_O
 
it was quite common for people to visit b&q on a Friday, buy a drill, put up shelves and return the drill saying it didn't work. Not that I would recommend such a thing.

I make full use of return policies but usually only when tools fail to live up to the advertising, can't bring myself to return truely handy tools ;)
 
Using a multitool in a bedroom is hardly dust free.o_O
No its horrible. I was hoping there was some tried and tested method/tool for the job. The vacuum attachements on the plunge saws look hopeful but maybe I should bite the bullet and go at it with the lump hammer :confused:
 
Spending a bit of time with some plastic sheeting and timber to make a sort of tented area helps
Make it big enough to cope with it collapsing as the vacuuming starts
All it does is help with the dust but better than nothing
 

DIYnot Local

Staff member

If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.

Select the supplier or trade you require, enter your location to begin your search.


Are you a trade or supplier? You can create your listing free at DIYnot Local

 
Sponsored Links
Back
Top