Search results

The boiler is a glow worm fuelsaver 40m/50b mk2

This is way the wiring is. I haven't touched it. I see someone has used earth wire on it. And on the thermostat they used a black sleeve on the earth

Hi im finally getting around to installation of hive. Its a 2 channel one that does pumped ch and gravity hw. Ive taken the old control unit off (ls241) The backplate fits the hive. The thermostat is a bg dial type rs2 . It has 3 wires that when metered out goes to the backplate (a neutral...

Yeah that sounds better . Go left from switch then up to fcu behind hood. . Cool will do that then decide if after its fitted to tile before or after hood is up. Tile to top, up to bottom or top of units . Thanks efl

Thanks for replay. I usually notch the noggin as it doesn't raise out from plasterboard surface. I can get it up (steady on I mean the cable) to top of unit , but its how to get it to the hood as it would be a inverted L shape and would fall fowel of the law. So its getting from switch . Up...

Connection from cooker circuit sounds ok as its just controlling 2 ovens that are on a 32 rdc ., but the work for channels would be much. It has 2 double noggins and a single, to go through as well as taking cupboard off, Was thinking about making a hidden safe zone. From a fcu straight up...

Of course its a full plug. A plug top is just a usless piece of plastic. It was the full lot.. with pins as well . Think that's why he wants it taking up into loft as it will go up the side in the safezone, then into loft and down to behind hood. Its getting vented via loft then externally...

Hob is gas and the supply is under the hob. It would be easier to take it right up middle to the flex outlet. And for a fcu fitted nxt to hob socket. Think he wants to make cash or put me off fitting cable.

Hi . Spark wired kitchen about 2 month ago. I told him I was going to put a hood up but didn't have it yet. As per pic you can see the cable he rolled up at top right, this goes to a trailing socket, he said I should just put plug top on and connect it to it ( wire going accross wall.) I...

Thanks for replying john. I think this can be done with just using a hammer drill and brick drill bit. Drill lots of small holes in a circle then use a bolster I was going to get a vent kit with flexible pipe but think ridged would be better as it won't collect condensation

Im fitting a cookerhood , one that goes to ceiling and can vent externally. The vent pipe that im thinking of using is rigid plastic with one bend. The hood will be just below loft space and my ventilation options are Vent via a soffit (but with air flow it might draw hot air back into loft...

Thanks bud. Will pull it out and fit other shelf

Hi just built new standard size larder housing unit and want to install 2 appliances. I have a single bosh series 6 combination oven and a series 6 single oven. I have put shelf in at appropriate height for 2 ovens , but I can't find any info on fitting them . Does one just sit ontop of...

Thanks johnd. The joist in corner is further down from end of wall so cant get to it . So will use the drill driver twist bits to take it. The cabinet will also hang on the other wall so should be secure

Thanks guys im looking at some on ebay . They don't say thickness though. Im going to extend it to the joist before the cabinet. ( will be covered by tall housing). But at end near corner their is no stud. So will use a redi driver , I think the 3 joist before it should hold it up. Its a run...

The easiest way would be the rail. But can only see it in small lengths from amazon. As long as its ok with going onto overhanging the end studs. The studs are wood. Any ware else sell it

Got the emails working now. Thanks bud. just wanted to check as it will come from hood. Across wall to spur but buried under pb so its not saw. I've another thread up about hanging cabinets .

I thought no one had replied as diynot is not sending email as it used to. Need to look and see why not

The socket its coming from is a fcu protected by 13a fuse. It goes to a single and double socket. (Total 6 amp). The hood would come from this to a 3a sfcu its the cable from the hood how do I get the flex across to the fcu without it being out zone

Hi guys and gals. Im hanging some b&q cabinets in kitchen onto a stud partition plasterboard wall. The old ones were installed with redi drivers . The new ones wont be no a stud. (recipe for disaster)I was thinking of one of these 3 ways . 1) use grip it plasterboard fittings. But think they...