Search results

Sorry - the panel is a texecom 48 Premier - less than 6 months - the com 300 is "new" but could be old stock? it is the 10 pin type

Hmm, Hi Sparkymarka, by you question I am wondering if I have bought the wrong thing.... I want to use it as a dialer to alert me by telphone call if alarm triggers - is it the correct tool for that should I use something else?

Hi all - can anyone advise please. I have installed a Com 300 (CTR21 Communicator PN CEA-001) onto The Texecom 48 Panel. Using Wintex I have: In "Options" Tab enabled the communicator - tick dial all numbers - tick In Tab "ARCs" I have enterd the numbers I want to dial In...

You've done it again Mark! your knowledge of this panel seems endless, thanks very much for your help. Problem now resolved.

I’m struggling with the subject setup. For overview I have 9 zones set as Area A (House). 1 zone (currently) set as Area B Garage. 3 Keypads all set with Area A & B ticked (Wintex). Keypads 1&2 are in the house, Keypad 3 in Garage. The XP8 expander has 1 zone (zone 9) used as A and...

You guys might be learning the odd thing from each other - I'm soaking up this info like a sponge! :lol: - I'm reading everything more than twice just to keep up with it. I'm very grateful to you both - Thanks again

Related to my earlier post http://www.diynot.com/diy/threads/set-up-texecom-premier-elite-48-for-2-areas.424782/#3299886 If I use OP1 (or more than one OP if needed) in the XP8 for the Area B Bell, how do I wire for the 5 wires that are used for the panel bell output using the OPs. Bell and...

Thanks Guys. I think I follow your tracks. I'll get the extra RKPs etc on order and get on the bench and see how it behaves. For me certainly it's one thing reading it and another thing doing it. I'll come back on this thread if I get stuck. Thanks again.

Hi Fellas, I have the bench setup for the alarm on the house sussed now (I think) thanks to some really top help from the forum. I originally intended to get the house sorted and then copy the setup with the same panel for the garage and workshops. Then I thought perhaps it could be done...

Picking back up on my previous thread http://www.diynot.com/diy/threads/wiring-3-contacts-in-series-to-texecom-48.423284/ I have now purchased the SC517s ready to go. I intend to use the FSL wiring option just want to be sure about the link cutting as the installation instruction shows for 2...

Thanks again, Yes these do look a better option. I should have asked you rather the guy that sold them to me :lol: Cheers Mark

I have changed the configuration of the contacts that I want to use across 3 sets of bifolders (these doors have been by far the biggest headache, thought I had a solution thanks to scott1980 with the Texecom Duel contact and viper but they turned out to be too larger footprint and fouled the...

Thanks again Mark for your time and information.

I have 2 panic buttons in series back to the Panel, I do have a spare zone on the expander but have them earmarked for later additions to out buildings. I also have used OP1 for internal sounder (sounding 1 minute in advance of outside bell) and have OP2 earmarked (please see further Q2 below)...

Thank you for your time and your comments; I will pass them on to my electrician

That's very re-assuring thanks fro your time and info.

Thanks Guys. The RIU-R12 12V Auxiliary Relay looks good Adrian. I had seen an Elmdene one Mark but is it 3 Amp (rather than 5A above). Adrian, will this be ok so switch all 7 through one RIU-R12 ? Much appreciated.

I'm looking for a 12V relay that on alarm will turn on Qty 7 30W LED floods (all on the same mains circuit). What rating of switching current will I need? I ask this unsurely as when sourcing the house dimmers for the in ceiling LEDs a 3W led needed about 10W of dimming capability (max 8-10...