Search results

Yes I was getting them. Perhaps maybe because it was connected via sky box and fed through its rf port using tvlink fd40 amplifier? The setup was Aerial wire into skybox --fd40 amplifier to rf port -- and 4 outputs to distribute the signal to different rooms. Now the new setup is aerial wire...

Hi Acurachris, Finally the electrician managed to drill the hole and got the wires in the roof . Works perfectly. I now noticed that even though using an labgear amplifier, i am not getting hd tv channels (before there was an ampliefier connected via redundant sky tv box. I have now removed...

Hi Acurachris Thank you for your reply. I have the ariel on the chimney. The wire directly comes into the lounge from the ariel. Connects to the amplifier and distributes to the other rooms. My lounge has a clutter of 5 to 6 wires and looks very messy despite tied with cable ties. To tidy up I...

Hi, I was wondering if I can please get some advice and help. I am looking to install tv amplifier in the attic and like to run some tv cables from the attic to the outside wall into the bedrooms. When I looked closely in the attic, I could not see any outside wall except the chimney. Also I...

Hello I was wondering if some can kindly advise. I need to get my TRVs changed as the pins are not coming up once its pushed down. Whilst getting the plumber to change the valves, I am considering to clean the system as well (I have not seen any dark water or anything but as the radiators...

Thanks Oldbuffer & terryplumb. Thats great. I suppose, I will get the TRV changed.

Hello I have a slight issue with 2 of the radiators at home. When the heating starts in the morning, the radiators get nice and warm but after a while they cool down and doesn't warm up some times and they remain cold. First I thought as the rads are about 11 years old, there might be a build...

hi I have had drayton wiser installed a few days ago when the kitchen was being re done. The electrician fitted everything and I checked the hot water and it was all fine.mgiven the high temperatures, I did not check whether central heating fires up or not until today. Unfortunately, the...

Hi I have hotpoint washing machine and from past few weeks its been making strange "tak tak tak" noise during wash and spin cycle. There is nothing stuck in the drum. Got an engineer to look at it. He advised to change the drum. He says its the problm between spider and drum. When he slightly...

Thanks Footprints; will try and re sand it again.

Hi I just jet washed my driveway last week and after it had dried completely, I got a weed inhibiting sand and brushed it between the blocks. I have noticed over this week when it rained, some sand has been washed away leaving my concrete blocks a very thin spacing between the blocks. - I am...

Hi Lucid Tried all the channels reception still not improved. Looks like its the Phone mast that is near my house is the problem after reading the post. I was wondering what if I connect these filters that are available to make sure the 4G signals are filtered??? What you think Many...

hello From last few days, I have been getting grainy picture on my sky through TV link in all my bed rooms. When I pull out the Ariel feed in my SkyHD STB until the centre pin is not connected but outer shield still is. the picture in my room becomes crystal clear and I can watch the free...

Thanks. Looks like I ll have to get an engineer out to sort this. [/url]

Hello I have a Hotpoint FDF 780 dishwasher; After I load the dishwasher, and start the cycle, it fills with the water and gives the hissing sound for a while but does not run or complete the cycle and in the end gives the error code A-8. Can someone please advise??? Many thanks in advance...

Thanks Bernardgreen. This has finally been resolved. Red and geeen wires in set abd yellow n black in line. Have not got any errors. I assume all is well. Cheers Lk

Thanks bernardgreen. Does that mean I have to hardwire the Black and yellow wires in the Visonic Control Panel's "Line" as well for the connection to be complete I think this is the only mystery now that is left for me to solve???? Thanks once again for your help. LK

After help from this forum I have now managed to hardwire (Red & Green Wires in SET pins of Visonic Control Panel and the RJ11 end Plugged in the Sky Master Socket via ADSL Filter. It says Line Failure when I read "ready memory" messages; and after a little while gives 3 beeps. I clear the...

Hi Europlex, Thanks for the prompt reply. I have the Phone connector pin that goes in straight into ADSL filter on the wall socket (RJ11 type). Its the Visonic CPU that I am trying to hard wire? I am not sure what colour wire will go in where? Any help will be greatly appreciated...

Hi, I am trying to activate phone connection in Visonic Powermax. When opened the control panel, I found the wires are not connected. There are 2 sockets (Line & Set) both have small connectors 2=line 2=set in which the other end will have to hard wired. I don't know whether all four...