Search results

No, not particularly. Standard 3 bed with a couple of large doubles then 5 regular singles over 2 floors. Because it's a digital pressure display which you need to activate, it's not as easy to keep track of any fluctuations. Since last top up to 1.3, it's now static for 3 days, although heating...

Contacted Boxt who the service plan is with and advised there may be a PRV issue to check on the service. They state that this would not be covered under a service, which seems odd because most services state 'inspect or replace' against items such as valves. However, they did pass it on to...

So, quick update. Topped up again to 1.2 last night with a view to isolating later today when everyone out for the day. Pressure stayed steady overnight, but dropped to 1.1 by 3pm today. Checked ziplock bag which is placed over expansion pipe and it has about 150ml of water in/bag steamed up.

Evening all, looking for advice. Worcester Bosch 4000 boiler, exactly 2 years old. Serviced annually, just due it's 2nd. Noticed lights flashing yesterday and pressure was .8. Usually check this fairly regularly but it's never strayed from 1.2. Topped up last night to 1.2 and it dropped to 1.1...

Wk100hb

Just wiring live/neutral does nothing. I've adjusted the humidistat/timer, I've even boiled the kettle under it, no joy. My assumption was that if I loop the permanent and switched lives together, the fan would be permanently live, but would only activate within a given humidity range.

I have two Domus H1 extractor fans which need to be replaced. I have purchased two Manrose humidistat fans. The fans appear to be on the mains circuit, rather than the lighting, and they are currently wired to permanent live/neutral only. The replacements don't work when wired up the same, and...

I live in an 1890's end terrace which has a half cellar. The wall which separates the cellar has developed a step crack, spanning about 4ft in height. It follows the mortar, although one brick has split. The joints in the cellar are a little eroded at points, and I think the crack is perhaps...

The BT line in my property terminates into what is obviously a secondary extension socket, rather than a master socket. Probably been DIY'd on at some point. Phone lines work fine, broadband works fine. As such, I'm not sure whether to worry about it too much but 1) is it likely to be missing...

Yes, seems fine cheers. Also, despite the strong winds, my roof hasn't flown off.

Just an update. May be coincidence - change in weather or some other factor - but since the laps were opened, the loft has dried out over the course of about a week. Will obviously keep my eye on it, but for now, this solution appears to have worked.

Really hoping to do it DIY - there's always a million and one things wants doing, so anything I can do myself is a bonus.

Unfortunately, I don't have soffits. The fascia boards seem to be attached to the last course of bricks, with the roof trusses ending on the wall and just a slight overhang of tile. Ive seen fascia vent strips, but I'm not sure how easy these would be to retrofit.

I'm having a problem with condensation in the loft - I've read all the stickies on this and other sites, and understand the causes/solutions. I believe that inadequate ventilation is the problem in my case, and probably has been since the roof was installed some years ago. It is concrete tiles...

Answer came back that an EICR would be a further £75+VAT, taking it to £355+VAT.

Thanks for the advice. Have asked for further clarification of what the price includes.

Example of one of the quotes... Dear xxx, To supply and install a domestic consumer unit as requested, the total cost would be £280 + VAT. In order to install the unit, it must be ascertained that the existing wiring complies with BS7671 prior to installation. Regards Would you...

And I'm assuming that such an electrician would charge to perform such a test and inspection - what kind of figure should I expect to see for that?

I have recently decided to collect some quotes to update my knackered old fuse board to a split load RCD consumer unit. Prices are coming back fairly satifactorily, but I've been told on multiple quotes that in order to install the unit, it must be ascertained that the existing wiring complies...

Just a quick question before I decide whether or not to make this my next project. What do you think would be a fair price for a consumer unit to supplied and installed (east mids area/3 bed terrace)? Thanks!