Search results

Hi EightyTwo, I've done that, RF cards set and unset perfectly when used with a keyprox, I just can't get my head around the max3 :confused: Josh

Hi all, after perusing the forum and reading one article on the installation of the max3, I have followed the cabling and install as per the post and confirmed it with the install sheet that came with my reader, but I still can't get the reader to set and unset the system when presented with a...

Hi, when I power it up the power led flashes then the fans stop and the warning light comes on, had a look inside and there's no obvious damage, apart from the cracked casing no loose cables or fuses (that I can see) Thanks JJ

Ignore my stupidity, I have figured it out... Thank you for your help :)

Hi EightyTwo, I think I get it, do you mean like this? G2 Zones by PhotographyJosh posted 30 Jun 2015 at 10:31 AM

Hi Everyone, I was just wondering if anyone could tell me how I wire 2 devices onto one zone on my G2-20? I would never normally but as it is not for an intruder zone just a fire zone, and I only have 1 zone free which has been earmarked for another device, and I just can't seem to figure it...

Hi everyone, I own a PRM 10 projector made by Promethean that used to work fine, but when I was mounting it to the ceiling I got an electric shock from the light fitting (which has since been removed) and dropped the projector from a height of approximately 3ft, it instantly powered off and...

Hi, a while back I asked a question about a hipath 540 PBX system, I finally got round to looking at it and it's working and all set up, I got the IP address sorted but for some reason I cant connect to the manager software, I have found a copy of hipath manager C, when I try to connect through...

Hi, I've got a G2-20, that I need to default and I've tried the suggestion form another post thread on here I have the old user code and have reset that to default but no engineer code, can anyone suggest another way of doing it? Thanks, JJ

Hi Rob, So I finally got the system setup and kind of working internally, I can call all internal phones and have setup some features via the *91 setting, but I'm having trouble working out how to setup the central phone book, how to setup auto attendant, and how to connect to the Manager...

Hi, I have a Micros Workstation 4 system and I cant get it to boot, I have no idea how they work, operate or boot. I was wondering if anyone has had any experience with these systems, do they require a HDD or are they slave systems that run over a network setting? If anyone could help me to get...

Hi, I ran a new length of cable for the AB, seems to have fixed the issue, but thank you for your help, Josh

RJ45? out of a 305m box no jacks just cable I laid in the beginning of the year, and it was working fine until I moved the panel and that's the AB for a keypad and rio downstairs

Hi, I installed a g2-20 earlier this year but due to unforeseen issues I have had to move to control panel, labelled all the connections and replaced a run of cable, wired it all back in exactly as it came out but the problem I have now is when I apply power the auxiliary power fuse blows and...

Hi, I currently own a Siemens hipath 540 PBX and 4 optipoint 500 phones (2 standard, 2 basic (RJ45 plugs)) and I was wondering, well, kind of desperately hoping someone could help me in installing the system to a fully functioning state, ready to plug the ISDN2 lines in when they are...

That's the same guide I've got, could it be for a later or earlier firmware release maybe? Josh

Thanks for the reply, in the installation manual I have got it says it can be either, I'll see if I can't hunt down a NC button and swap it out Thanks for the help, Josh

Hi, I'm currently wiring an exit termination button to my G2-20, the button is normally open and wired with a 1K resistor over the contacts and a second 1K back to the panel (drawing below) as a zone would be wired, when I do this it sets immediately without the button being touched, all the...