Search results

Having had to softener installed for a number of years and then having it sit in the garage for a while before re-plumbing my new home. I started to have issues where the water would be soft for a maximum of four days before turning hard and requiring a few manual regens to get it up and going...

As I understand, you have an overhang on one edge of a flat roof to take the fall and hold the guttering. So then two side edges of the roof have the upstands and you can see the gentle slope. What can I do if I want two sides of the roof to overhang? Say for example the front and one side...

I've a 203x133UB25 beam ready to be installed across a double garage opening, it will have a wall plate fitted and hold one end of the timbers of a flat roof, may also hold the double garage door later 2 questions 1. Is it undersized? Ive been doing some reading and seen people are using 203 x...

Just finished the single skin blockwork for my double garage and moving onto the roof next The double door opening has a steel in position, the top of which finishes at the same level as the rest of the walls (side and back) I now need to move onto building the flat roof structure and am...

Thames water were out doing some work on my neighbours water meter today. So I asked them to do a pressure test for me as I've recently noticed a drop in pressure My mains pressure was showing at nearly 4 bar, at the meter. But when I test immediately after the mains stopcock inside my house...

I live in the Hounslow borough. Have/are just about to complete a 6m permitted development rear extension. I would like to move onto a double story side extension and a loft extension. Id like to make the most of the space and work smart. Would it be better to do the double story side and...

Had boiler repaired recently. They had to shut off the mains stopcock outside to do some repairs to the boiler, and since then the water pressure to the house has been abysmal. Ive been outside to check it's fully opened at the mains stopcock and yes it is. But the pressure is so low now. Any...

Hi all, Pyronix euro 46 V10 self install. Been working fine for 1yr. Recently my full set, final exit stopped working. I'll set to leave the house. Sometimes when I close the front door (wired contact) the alarm won't set, might keep beeping, then I re-enter and close door it'll set. Then...

Have setup my euro46 panel. Full set A works well for me. I set alarm, choose A. Timer starts, if I open and close my final exit the timer stops, alarm sets and confirmation noise occurs. When I return open the front door, timer starts, I then have time to unset. The problem comes when I try...

Until now have been using the master manager code as my user code to set A and B. Have been into the master manager menu, added a new user now for someone staying with us. This person when inputting their code automatically arms, I've allowed it to set unset A and B, but it doesn't give an...

Trying to fullset, have front door set as final exit. Put in user code, set for A. Said leave from final exit, the countdown started, left and then a full tone came after closing the door. But that full tone from the internal sounder won't stop. What have I done wrong?

Is there anyway to have different volumes for setA and setB. For example when setting for Bbed I'd like it to just beep confirm rather than a loud countdown to wake the kids.

Just getting round to programming this. Have 9 wired inputs - 8 sensors, 1 front door contact (wired to keypad) Have wireless zem installed with 2x wireless door contacts Now trying to programme. Wireless door contacts set themselves up on input 17 according to wireless install in engineers...

I am trying to wire a magnetic door contact with the pyronix euro V10 system. I have these...

Hi all, Need to change the pump head in my Worcester Bosch combi boiler. Is there a way for me to isolate and drain only my boiler to swap out the pump? - if so could anyone assist. Or do I need to drain down the whole system?.. Boiler is Worcester greenstar 35cdi Thanks...

Ok a few of you will know my last few posts of swapping out a 3 port valve for 2 X 2 ports, and wiring in hive for CH and stats for UFH. All controls fine, valves open, boiler fires... and so becomes my next problem The boiler, set at 5 on the HW dial, gets a call for heat. Heats up, gets to...

Hi guys, after a bit of help... Have just wired up my system with a hive and UFH setup with zone valves. All working great thanks to help from everyone here. The problem I have found is that the system will only fire (when for example hive calls for heat), if the built in timer is plugged into...

So I've managed to get 2 zone valves plumbed in, one for my CH, one for my UFH. Now on to wiring. I am using a Worcester Bosch 35cdi combi. Wiring diagram attached. I have also drawn what I think is the right wiring plan, but would like a little look over help please, anything a miss? I've...

Ive got a few hikvision cameras which I mounted today. The junction boxes make these cameras look like isores. Does anyone know of any slim ones or an alternative? Need this because the hikvision cameras come with such long wires and a huge female rj45 socket connector. I was thinking about...

After a bit of help with the wiring for my boiler, CH and UFH. All plumbed in but the plumber has now done a runner and I'm out of money. Figured I can do this myself (just wired in my alarm system), plumbed and done electrics before. I'm just stumped with how to setup the S wiring. Here's...