Search results

Hi all, I have a large driveway, approximately 35 sqm. To the right, I share a boundary with a neighbor who also has a driveway. Currently, I have a block paving driveway and I'm looking to install (3ft) fence paneling along a 3-meter length to create a partition between my property and my...

Hi, all I have just finished my wetroom and tanked all areas, to my understanding because this is a wetroom, therefore, all areas should be tanked. However, I have created a large concrete step that is spirit levelled and my worry is if I tank this area then should any water ingress via...

Hi all, Just finished, tanked and tiled the wet room. Would like to use epoxy grout. Does anyone have any recommendations, please? I have all the cleaning at hand because of the haze epoxy causes on surfaces, so ready for. I just need something waterproof and resistant with a reasonable...

Hi All, Just finishing my wet room. I have a linear drain in the end embedded and secured levelled into the concrete floor. I am now ready to do the wet room slope pan. I have placed two pieces of strip wood on each side and raised them accordingly to my slope measurements. I will use these...

Hi All, I have installed my linear drain, levelled and position it in place with concrete and followed this with levelling compound a couple of weeks after to smooth and level the floor. I am now ready to create my mortar bed slope (Shower pan) from the curb step to the drain however I want...

Hi All, Hope you can help. I am just wondering whether I should backer-board the concrete block bench in my wet room, applying it with a tile adhesive. Or can I tile directly on top of the concrete block work? I worry about moisture or cracks within the concrete block/to tile directly on...

Hi guys, I am in the final process of completing my wetroom prep before tiling. All that is needed is the waterproofing and my mortar bed slope to the linear drain. I have applied waterproof backer boards, now I am ready for tanking/waterproofing. My question is should I fully Tank my backer...

Hi All, Currently renovating an old wetroom. 1. Removed everything back to brick. Currently, Have stud battened the walls, insulated the spacing and am now ready to apply the tile backer board, however, before I apply the tile backer board. Should I cover the insulation and battens with a...

Guys having a wet room done, battened walls and aquaboarding etc... wetroom is downstairs other side of the wall is external, plumber used bitumen flash primer (white spirit based) on the walls before applying the battens to ensure that damp doesnt penetrate the batten on the interior. Sadly...

In what order would you create a wet room? Renovation. I have stripped the old wet room back to brick. I just want your guys opinions on what order you would do things from materials used to completion. I will have concrete block benches, screed slope floor to the drain, and shower head mixer...

I have stripped the old wet room back to brick. I just want your guys opinions on what order you would do things from materials used to completion. I will have concrete block benches, screed slope floor to the drain, and shower head mixer etc... but as for everything, what order and how would...

Hi, Guys would like your advice and opinions please concerning my wetroom renovations. I have stripped the walls back to bare brick and removed the previous concrete screed. Sadly, the previous screen was done by someone who didn't slope it correctly allowing water to flow out of the wetroom...

Hi Guys, I have made an 85cm x 75cm concrete formed countertop (40mm (4cm) thickness). Currently, this is the third day, I removed the concrete from the melamine form and its perfect. I have covered it with sheeting and kept it wet thoroughly since day 1 every day, I will continue to do this...

Hi guys, I have just installed brick slips in my home and I am looking for the right mortar mix/ratio between sand, lime, cement/ White cement and water (or pigment colour) to achieve the desired colour below please, in addition to achieving strongly bonded mortar. Below is the colour, its a...

Hi guys, I have just installed brick slips in my home and I am looking for the right mortar mix/ratio between sand, lime, cement/ White cement and water (or pigment colour) to achieve the desired colour below please, in addition to achieving strongly bonded mortar. Below is the colour, its a...

Hi guys, I have just installed brick slips in my home and I am looking for the right mortar mix/ratio between sand, lime, cement/ White cement and water (or pigment colour) to achieve the desired colour below please, in addition to achieving strongly bonded mortar. Below is the colour, its a...

Good Evening, Was hoping you could help me please, I have been a homeowner of my property for 25 years, Mortgage paid off and I have my title deeds ownership of the home. We had a back garden extension built 7 years ago, though, before this, we had a wall and wire fencing which partitioned both...

Hi all, started using the diamond range from Dulux yesterday, hot day, add around 7% of water added to help consistency. It was quite smooth anyway, though, thought add some water would help. Though as soon as roll paint on walls and final lap the wet edges 3 mins later, literally the paint is...

Hi all, started using the diamond range from Dulux yesterday, hot day, add around 7% of water added to help consistency. It was quite smooth anyway, though, thought add some water would help. Though as soon as roll paint on walls and final lap the wet edges 3 mins later, literally the paint is...

Hi guys, I am having serious problems with this Paint finish (Diamond), i opted for highest durability finish tinted colour (dusted moss 4) to paint over my 5 year old emulsion painted wall.Though i have been having a nightmare with this paints drying times. It is just drying way to quickly...