1. Visiting from the US? Why not try DIYnot.US instead? Click here to continue to DIYnot.US.
    Dismiss Notice

Baxi 105e

Discussion in 'Plumbing and Central Heating' started by Ken55, 26 Apr 2020.

  1. Ken55

    Ken55

    Joined:
    26 Apr 2020
    Messages:
    4
    Thanks Received:
    0
    Country:
    United Kingdom
    Hi.all
    Looking for some help with my baxi 105
    Has had a few new parts fitted...
    New pcb, diverty, blow valve.
    Wireless salus controller installed.
    problem now is that it powers the ch on without calling for heat, also with the control knob turned to water only. Only way to switch the ch off is to lower the temp knob right down. This happens randomly. Any ideas.
    thanks
     
  2. Sponsored Links
  3. easyflow

    easyflow

    Joined:
    12 Jan 2008
    Messages:
    472
    Thanks Received:
    60
    Country:
    United Kingdom
    Sounds like problem lies with the salus thermostat, someone nearby is controlling your c/h with their thermostat.
    Reconfigure the pins in the wall stat to change frequency (go to instructions).
    If problem persists get your GSI to disconnect the thermostat wiring to the boiler and re connect link so the boiler uses its own thermostat.
    Other than that due to the work the boiler has undergone could be water/damp within the pcb.
     
  4. Ken55

    Ken55

    Joined:
    26 Apr 2020
    Messages:
    4
    Thanks Received:
    0
    Country:
    United Kingdom
    Hi. Thanks for your reply.
    The pcb is dry and brand new did change that first. the red light on the receiver on the boiler normally lights red when calling for heat but it’s not lit when the boiler if firing up lady the control know is switch to hw only. But still fires up.
     
  5. Chris_W

    Chris_W

    Joined:
    26 Sep 2019
    Messages:
    5,091
    Thanks Received:
    1,393
    Location:
    North
    Country:
    United Kingdom
    Try removing the switching wires in your Salus, if this solves it,you’ve found your problem.
     
  6. Sponsored Links
  7. ianmcd

    ianmcd

    Joined:
    15 Aug 2010
    Messages:
    19,767
    Thanks Received:
    7,698
    Location:
    Lanarkshire
    Country:
    United Kingdom
    are you sure you have a 105E and not a 105E instant, they are not the same
     
  8. Ken55

    Ken55

    Joined:
    26 Apr 2020
    Messages:
    4
    Thanks Received:
    0
    Country:
    United Kingdom
    Hi. it’s a combi.
    could it be a faulty frost sensor as it turns the ch on even when it is on hw only? so Carnt be the salus ?
     
  9. gas112

    gas112

    Joined:
    27 Oct 2009
    Messages:
    20,040
    Thanks Received:
    6,919
    Country:
    United Kingdom
    When the heating is on when it shouldn't be is there any demand lights on, the tap symbol or rad symbol
     
  10. Ken55

    Ken55

    Joined:
    26 Apr 2020
    Messages:
    4
    Thanks Received:
    0
    Country:
    United Kingdom
    Hi
    Yes the rad symbol lights even when knob is switched on to hot water only. The light on the receiver for the room stat isn’t on.
     
  11. DIYnot Local

    DIYnot Local

    Joined:
    3 Sep 2019
    Country:
    United Kingdom

    If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.

    Select the supplier or trade you require, enter your location to begin your search.


    Are you a trade or supplier? You can create your listing free at DIYnot Local

     
Loading...

Share This Page