Search results

  1. C

    Bosch SGS43C12GB/08 dishwasher problem

    Hi, I must admit that when replying I have had a different model in my mind so have been asking you to look for wrong things, although they all work the same ish. I have been "Told Off" for "Railroading and prolonging this thread when it is obvious that the control board has gone" So I...
  2. C

    Zanussi DR50 fridge

    The thermostat phial may have come disconnected from where it attaches to the ice box, or a faulty stat, because when you push in "the red bar" you are talking about the ice box should defrost, but it will not defrost if the stat phial is not connected (cold) Good luck Colin
  3. C

    Freezer Temp Alarm

    A. Is the freezer running when the alarm comes on (before you turn of FF) B. What's the temperature in the freezer Colin
  4. C

    Bosch dishwasher water inlet problem

    don't think mouse poo is the problem. If it happens again just try and push the door, without tilting machine, if it doesn't start open and close the door. If you need to post again include model number. Lets hope it runs forever!! Colin
  5. C

    Any views on neff s51m63x1 integrated dishwasher?

    So it's filling and washing just no heat? Check connections on heater, and a cut out I think on that model, also check for dry solder joints on timer board. If there are any just resolder Colin
  6. C

    Bosch WAA28160GB

    Yes, no power through it, if you have a meter when it stops filling disconnect from mains remove wire from one side of valve and see if you have any resistance there. Colin
  7. C

    BOSCH SGV53E33GB Dishwasher - fills/empties/fills/empties...

    Just try rocks1 advice, if it's under warranty it would be best not to try anything! Colin
  8. C

    Bosch SGS43C12GB/08 dishwasher problem

    Are you any further forward? Colin
  9. C

    BOSCH SGV53E33GB Dishwasher - fills/empties/fills/empties...

    If the machine overfills or thinks it's overfull it will pump out. Take off left hand side of machine and put it on a wash cycle. The water will come onto the regeneration chamber, come out at the bottom right of chamber through a grey hose. If this hose is partially blocked, water will "back...
  10. C

    Smeg tripping.....no heat

    Yes I would think replace the element you mean? Be careful, too late now for you, running on an extension lead as some don't have an earth connection, may be why it didn't trip rcd, which could make your oven/appliance chassis/casing live when testing Colin
  11. C

    Bosch WAA28160GB

    Wouldn't have thought 15sec. enough time to fill any machine, more like 1min, a little dependant on water pressure. I would look at water inlet valve, when it cuts out turn off machine for 15mins and try again to see if the valve is overheating and going open circuit. Once empty can you put...
  12. C

    Bosch dishwasher water inlet problem

    I think that when you tipped machine water cleared from the bottom tray, where the motor is etc. so now the anti flood switch is not activated via the float polistyreen circle on the left hand side. When using the machine now look in the sides to see where the leak is coming from. Sometimes a...
  13. C

    Any views on neff s51m63x1 integrated dishwasher?

    Fix the old one, will probably be more reliable then than a new one!!! Colin
  14. C

    bosch 1200 exxcel washing machine

    Door catch engaging, Locking? (can't open door) With your test meter you will be able to see if you have neutral return, ie 240v across live and neutral, but then if door is locking it must be there! Yes I have had suppressors going o/c Good luck Colin
  15. C

    Candy Grand0 GO1282

    I would clean carbon from between armature segments (carefully) and run up on a bit of commutator stick or very fine wet and dry (dry) to clean com. I suppose what you have used is the same make up as switch cleaner, so would evaporate. Never used it myself. Colin
  16. C

    Biasi Riva Compact HE water over heating

    I thought this fault may have been too complicated for the people on here to diagnose, seem I was correct. Have fixed it now with some excellent advice from a really good forum elsewhere!!! Really simple fix.
  17. C

    Candy Grand0 GO1282

    Oh, I didn't know that it would give an error code, just thought the module would think washing out of balance and keep adjusting speed! Colin
  18. C

    Candy Grand0 GO1282

    I don't know this machine, but sure it will have a speed control tacho on the end of the motor, a coil and a magnet. Occasionally the magnet can come loose and slip when the armature turns thus giving wrong feedback on speed to the module. Easy check to see if it turns freely on the armature...
  19. C

    bosch 1200 exxcel washing machine

    Think your going to have a problem unless you have a test meter. Is the door locking, if not try closing door and have a fiddle with the handle to see it engages the catch. Look for burnt wires on terminal block, follow where mains lead goes in, check suppressor. You know? you...
  20. C

    Bosch dishwasher water inlet problem

    Tip it at least 45' to the right side or rear wait for a 45sec to let the water drain out, put a towel down, 1/4 pint, then try again. If it works take the sides off, open door 2 screw either side, and see where the leak is coming from. Could well be something simple! Good luck Colin
Back
Top