Search results

I know this thread is a year old but I am having he same problem with my Panasonic SD 2511, been using Panasonic bread makers for years but I keep getting the odd flat loaf, they haven't risen but it looks more because the top of the bread has burst so letting the air out, I'm thinking it's...

Nice one Gazman, your a star..

I've got comparable quote from 2 local companies for supply only PVCu , one is a small company that uses Eurocell profile and the other is a large company using Tricept Profile, both order them in rather than make them. Any advice on which is the better window? I'm inclined to go with the...

WE DID!

The part was leaking which was causing the pressure problems we kept getting.

Thanks for the quick replies, well the first guy did say he wasn't sure but the Diverter was common, he didn't think much of the boiler. We had him (at least I think it was him) 2 years back replace the hot water switch. All the parts were new from online dealers, he asked me to get them to save...

We have a CB24 that broke down with a solid Red light fault, we could reset it, it would go through it's firing sequence but never fire up then the solid Red light comes on A. A local plumber took a look then ordered a new diverter valve, he fitted this but the problem remained, he then got a...

Got a solid Red light on a CB24 , we have replaced the diverter valve , the flow switch and recently the overheat stat to solve a new problem of a solid Red light. Boiler tries to fire, spark is there, but it won't start. Have cleaned the system and heat exchanger and pump is working. Only thing...

Any help would be really appreciated I have a 2 year old Limefighter that has started leaking from a crack in the body, it must have got a knock, it's on the C inlet to a Gledhill Cylinder , I went to get a replacement but they have been superseded but after bit of reading they aren't really...

Thanks again for the reply Alec, It is the 470f I just suspect the internal sensing is incorrect, interestingly I put it outside today for the last 2 hours, and it showed the weather sensor as 11c and it's its temp was 13c, so the sensor is working but I suspect it's a few degree's more than it...

Yea thats it Alec, it's freezing in the house at midday and it's showing 22c, that can't be right, I can check with the old manual thermostat thats still on the wall and it's clicking about 17c, I'll ut it in the garden tomm and see what the bloody thing does!

Got a new Ecotec plus system boiler and 470f weather compensator all in and working fine, even got the VR10 HTC HW stat working for full control but I think the remote isn't setup right, when the boiler is off during the day, the temp on the front panel says 22c when I know it's around 17c I can...

Thanks for all the replies, thats great..I was going to wire in my old S Plan but I think we shall go with the Valiant new controls it should shave a few more percentage off the bills. at least its quite easy with the VR65 and wireless thermostat.

I have a new Vailant System boiler with Gledhill indirect unvented tank, and we're deciding on the system controls, I think it's going to be easier to fit the VR65 & weather compensator VR470 than use the existing, but one thing came up. Vaillant are upgrading the VR65 to 66 this gives an extra...

Yes a very good point Alec but I think they are def the future even tho a gimmick right now. Why develop an expensive programmer/thermostat with set features that is pretty hard to update in any way when a much simpler heating controller can be used and operated from a smartphone/iPad device...

Ah good points picasso and Alec, my first choice is the Vailant weather compensator I just thought this is going to look all old hat in a year or so with the home automation and ease from smart phones and tablets, that can sense when you leave the building or to operate when away from home...

Nobody used a wifi controller here? For anyone else finding it as hard as I am finding info on these things, it seems they are all the rage in the US with some being pretty cheap. I got a useless reply from Vailant simply saying there isn't a 24v connection, but not telling me what the...

Thanks to the advice here I have a lovely new Valiant 624 system boiler with a Gledhill 180L indirect unvented cylinder, but I am undecided on what thermostat to run it on, my old system is ok but 18 years old so I have been looking at the new wifi programable thermostat's but they seem mostly...

I wish CBF it's not covered they said..18 years ago it was not that long a guarantee , I think thats why it's been loosing pressure all these years, just now it's started actually dripping out.

Yea def a weird one I spoke to Megaflow and they think it's a split int he cylinder itself, so when the gap disappears water starts to seep out. It's def not coming from any joint. like from within the foam insulation at the bottom of the cylinder. I think system boiler then , replace like for...