I'm reroofing a porch roof, approx 3 square metres. Planning on 18mm ply (joists are sound) with EPDM on top.
Is it worth spending time and money getting firestone rubbercover, or would something generic like 1.1mm EPDM with adhesive from rubber4roofs be as good?
Looking for advice please. I've got a flat roof single storey bathroom that needs a new roof and I've looked at GRP Fibreglass as the route to go down. I also wanted to insulate the flat roof and have read all the advice stating that a warm roof is superior to a cold roof. If the Celotex for the...
Hi all, I have a wall that is above a flat roof extension, the flat roof is felted and gravelled, I have to remove some very poor mortaring from the brickwork, the mortar will eventually need removing as it is a different colour to the rest of the mortar but for now all I have to do is remove...
One of the many little gems I've come across when renovating my house is that my flat roof is a cold roof - the insulation sits directly upon the plasterboard with a gap above between the insulation and actual roof.
I'm contemplating converting this to a warm roof as I may as well do it now...
Hi All
I am looking to buy a semi-detached property which currently has a rear ground floor extension (extension also goes slightly down one side of the house) and as the roof needs re-felting etc. I would like to know/clarify whether changing this roof to a pitched roof would require Planning...
Hi, hope I have posted in this in the right section of the forum..
i'm getting a loft conversion built - the builder has put 25mm of insulation above the joists and 120mm inbetween the joists in the flat roof. he's said this makes it a warm roof therefore it doesnt need any ventilation..
is...
Hi all,
We are having a single story extension built. The house was originally built as one of a pair of similar properties in the late 70s. Our neighbours already have a single story extension with a flat roof and parapets. Due to this, we opted to go for the same style of extension to keep...
My wife has very kindly volunteered me to replace my mother in laws flat roof. Last year one of her neighbours was doing some painting outside and it appears he damaged the roof (which I'm guessing was already rotten).
So my plan is to remove the existing felt and ply and replace in reverse...
Hi Everyone,
First post so please be kind :-)
Seeking some advice to change my corrugated roof to a flat felt system. My garage is joined to the neighbours.
Currently the plan is to remove the roofing sheets, add a new lintel over the garage opening, add strengthing battons every 4ft to the...
Hi all,
I'm building a timber framed garden room with a flat warm roof.
my build up for the roof will be:
joists
18mm OSB3 sub-deck
vapour control layer
100mm foil backed celotex GA4100 or similar
11mm OSB3 top deck
EPDM
My questions are:
1. Do I need a VCL considering the foil on the...
Planning on using a torch on cap sheet direct to fresh osb without using the recommended underlay...is this a bad idea? If the cap sheet is bitumen backed and therefore fully water proof and has good adhesion to the osb I'm struggling to work out what the underlay actually does...unless I'm...
Been looking for weeks but cannot find any specific details on this;
I'll try to explain but apologies if I waffle. I'm building a garden studio, timber frame, without overhang. The top of the cold roof has 25mm air gap above celotex insulation then osb roof, then will be epdm. The walls have...
About to wrap my timber framed garden office with the breathable membrane and battens but am unsure how the edge detail is finished with an EPDM roof. The cold roof rafters end flush with the stud wall rather than any overhang.
If I go by the limited diagrams seen so far (see attached), then...
I have searched high and low and not been able to find a solution to my problem. I want to convert my garage to a bedroom. It is the link between two bungalows with traditional pitched rooves.
My problem is that the joists run at a right angles to the normal path of cross ventilation, across...
Hi all... hope you can help, I'm finding conflicting information online!
I'm about to put a GRP warm flat roof on an outbuilding, I'm using 100mm PIR foil backed insulation and was wondering do I need a deck between the joists and insulation or only one above the insulation (the joists are at...
Hi,
we are in the process of buying a 1960s Bungalow that has a 6% pitch flat roof. According to the survey, it recommends replacing the roof some time soon. I've enquired about replacing this with Single Ply Sarnafil but have been quoted £25k.Having done a bit of online research I came across...
We had a new 45m2 warm construction flat fibreglass roof installed in October. It makes intermittent loud banging and creaking noises. It is worse during the morning and evenings when the sun rises/sets and the temperature rises/falls. The roof is south facing. I have found numerous old threads...
Hi all
I've bought some celotex insulation to put up on the ceiling in my garage but I'm not quite sure on the ventilation. I want to place the whole sheets underneath the joists to seal the roof structure from the garage room. This is a cold roof configuration I understand. I'm not living in...
Hi
Sorry for the vague title, I have rain somehow get through and starts to seep down the plaster by my living room window
My property is a flat roof terraced, it has hardly any brickwork because it has one whole length of wall between two columns of brick that separate me and my neighbours...
Hi all,
I've just done my first flat roof and I've left noggins to pick up the Fascia's where the joists run parallel to the wall. The joists overhang at the front also for the fascia. The brickwork is two course higher on the outside so I could have a smaller fascia board by the time the warm...