plastering

I have a stud wall that has finished depth of pretty much spot on 100mm I have planed timber door lining that is about 108mm is 4mm on each side too much to ask of skimcoat? should i be thinking of getting 2-3mm off the door lining timber or is there smarter ways to do this?

Hi All, like to think I'm generally competent diyer, though regards to plastering have only ever patched up existing blown plaster. correction: 13 years ago dot dabbed drylined garage to room conversion and tapped all joints before pro plasterer called in , he was complementary of my work...

Hi had my kitchen ceiling skimmed about 5 weeks ago, over the top of the old ceiling which was just in a bad state. It was boarded originally. Everything has been fine, until yesterday, I noticed a yellow stain in one of the corners. Ironically it’s the corner than dried out first after...

Hi, our boiler packed in and we're having a new one installed in a couple of weeks, along with new radiators. One of the walls with an existing radiator needs replastering, and more replastering will need to be done around the old back boiler site once it's been removed. I'd far rather get the...

After 3 years of being in our house we've finally come to do up the dining room which is an extension built in the late 80s. It's freezing in the winter because it's essentially got 4 external walls - 1 backs onto garage, 2 are external and the other one is the old external wall of the kitchen...

Hi All, I’ve been having some work done in the garden and as part of that I’ve had the garden wall rendered, the company I’m using have subcontracted the work out and I’m not very happy with the finish. I’m hoping someone will be able to guide as to what’s gone wrong and give me the knowledge...

Can anyone help me with this? The online calculators are pretty basic and don't really do the job. Am in a reasonably prosperous town in Wales. Have had prices of 1.5k and 2k? Any help would be appreciated. 5x4x2.3m room. How much is reasonable to pay for: A) 2 coat skim on pre boarded TE...

I had a go on my first dot and dab for my boiler cupboard ready for plumber to come dowm and first fix. Considering there is no multifinish plaster at moment all around the country. can I plaster/skim the plasterboard directly with bonding 60 of british gypsum or ideally need to wait for a...

As I had now removed most of my hard plastering inside the house due of the age and completely came apart from the wall. I was suggested to use dot and dab plasterboard system instead of plastering the whole house. Can someone advise on pro and cons of each method and which one would be the...

Hi all Renovating our first house slowly. Neither of us any good at any forms of DIY Had a room rewired as plug sockets were still the originals which meant the deep shirting boards needed to come off..... What we are left with is holes! How can they be re fitted once the plastering is done...

Can I just ask when you have two sockets with with about a few cm in between how do you plaster or fill in between them or does the face of the sockets cover them. The thing I am referring to is I have a two gang socket then a small gap about a cm or two and then an Ariel socket. There needs to...

As the lockdown is slowing everything down and no delivery at moment. I was wondering what would be the best plasterboard brand to use. Moast DIY sell Knauf or Gyproc? Are those any good? As I live near a train line I was wondering to use soundblock for ceiling as well. Is it worth the extra...

I found out that the ceilings on my first floor were renovated but the laths were kept and pins were used instead of screws. My first question. Is it worth to remove the old plasterboard attached to lath and replace with a fresh one and maybe just tape and joint or new plaster? Why the lats...

Hi all, So I'm plastering onto a wall and needed some pregrit. However can anyone tell me what the difference is between yellow and blue pregrit? Any recommendations as to which ones to use/avoid?

So I'm a little confused as to what the plasterer is supposed to be doing having had some different advice. I've taken the walls back to brick in my 1930s victorian home. I have spotted some damp in the kitchen so got a damp specialist in to have a look. He noted some of the work of the...

Hi, I have moved into a victorian house which had a dripping stopclock in the cellar, which has been fixed up and has now started to dry out. Now looking at the plaster in the room above it. I have taken a picture of one of the (Edit: internal brick) walls, that was under the woodchip...

Leopard spots on wall after fooling in 2015 gas turned of for 2 years caused by leak and there maybe exposed asbestos from popcorn ceiling

Hello I have a hole in the wall from an old power socket which I would like to fill in and then skim with plaster. What's the best way to fill the hole which gives the plaster layer something good to adhere to? Thanks for your advice

Hi All First time post, hopefully someone in the know can help me out. Currently in the process of having my fully bathroom renovated. It's been tiled and grouted the issue now is the plumber doing it has said the cabinets are too heavy to hang on the plastered/tiled wall. Theres a mirrored...

Hi All. I plan to install internal french doors into a gap but I need to add some stud-work on either side and a header plate. One side the stud wall will meet an existing wall at 90 deg so straightforward. However, the other side needs to join onto an existing section of wall. This...